CE8407W2-PCE8407W2 Whirlpool Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Marvin from Warren, NJ
- Parts Used:
- WPW10116735, WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
AMANA Dryer Would Not Heat-Up
My problem was that my AMANA dryer would not heat. The site suggested testing the two thermostats so I opened the dryer but didn’t follow the instructions in the video tutorial on the site since my AMANA is different. I used a nut driver and needle-nosed pliers for the whole job. Here’s what I did:
1. Unplugged the dryer.
2. Disconnected the exhaust pipe at the dryer.
3. Pulled dryer away from back wall about two feet.
4. Removed the two bottom panel screws (floor level) and removed panel.
5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.
6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).
7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)
8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.
9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.
10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.
11. Used the belt to lift and remove the drum through the front opening.
I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.
I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.
Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)
I closed up the dryer by reversing the opening steps.
1. Unplugged the dryer.
2. Disconnected the exhaust pipe at the dryer.
3. Pulled dryer away from back wall about two feet.
4. Removed the two bottom panel screws (floor level) and removed panel.
5. Removed the two door panel screws and removed door panel by pulling out at the bottom until the two spring clips released from the top panel.
6. Noted the colors of the wires going to the door switch and removed (green, black and white from left to right).
7. Noted the colors of the wires going to the lamp and removed (bottom - black and top - red.)
8. Removed the two top panel screws, lifted up the top panel and leaned it against a support.
9. Removed the four bulkhead screws and carefully lifted up and removed the bulkhead being sure to support the drum. Took note of the belt path around the motor and idler pulleys.
10. Reached under the drum and took the belt off the idler pulley and motor drive pulley.
11. Used the belt to lift and remove the drum through the front opening.
I noticed that the internal vent pipe had become disconnected (which probably caused internal overheating) so I fixed that.
I then removed the wires to the thermostats and tested both for continuity. The limit thermostat was bad. I also saw that the belt was becoming cracked. I ordered a new limit thermostat and belt.
Installation of the new parts was a snap. I removed the old thermostat with the nut driver and replaced with the new one and pushed the wire connectors back on. Replacing the belt was a little trickier but not a problem. (Be sure to route the new belt correctly as noted on Step 9 and place ribbed surface next to drum.)
I closed up the dryer by reversing the opening steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Dexter, IA
- Parts Used:
- WP37001042
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Load noise when the dryer was operated
Followed the procedure from the video attached to the part in the web site. Everything went smooth. Did a major clean out of the cabinet, motor and vents before I put it all together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Fairfax, VA
- Parts Used:
- WP40113801
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
No heat
The video on the site was very helpful in completing the repair. The one suggestion I woul make is to check the actual heating element before ordering the Thermal Fuse. In my case the new fuse did not work because there was a break in the actual heatng coils. I replaced the heating element and it works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRED from ELK MOUND, WI
- Parts Used:
- WPW10116735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Dryer would overheat at all temperature settings
replaced the limit thermostat,thermal fuse, and cycling thermostat. Bingo. Problem solved. Noticed that the back of cycling thermostat had a buildup of lint and I'm wondering if that acted as insulation and caused a wrong reading of temperature. Did not have to disassemble dryer as I could reach all parts with lower front panel removed. To make it easer to install new parts with one hand I lightly hot glued the screws through the new parts and taped the upper portion of new part to bulkhead. With everything lined up and no need to hold the screws I was able to attach using one hand. It was a reach but easily done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Hawthorne, FL
- Parts Used:
- WP40113801, WP40111201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer had no heat
I pulled the heating element loose and layed it on the floor so I could see if the elements were heating. This required totally disassembling the dryer from the front including removing the drum. Then I bypassed the door switch so the dryer would run disassembled. Then plugged in the dryer and turned it on. Heating coils did not glow... Hmmmm. Put a meter across the two thermal switches mounted on the element assembly to find one of them was open. Ordered switch from PARTSELECT; ordered a belt too while I had it apart. Parts came very fast and reassembled with new parts. WORKS LIKE A CHAMP!!! Thanks Partselect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- april from lexinton, KY
- Parts Used:
- 61927
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
dryer not heating up
removed old element, relaced with new element , thermostat dryer works better than it has in along time
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from Alexandria, KY
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Install new latch
Just snapped the new plastic latch into the hole (the hole was there because in trying to extract the old latch, it fell into the inside of the door). Took two seconds. Order to arrival of the part took only 22 hours!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Wellsboro, PA
- Parts Used:
- WP40111201
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Replace drum belt
Leaned machine back and put blocking under machine to elevate. Removed two screws from front of bottom panel. Lift panel out and set aside. Next remove two bottom screws from door frame. Pull bottom of frame out and up to release. Remove wire clips from door light and switch. Set door frame aside. Inside drum, take three phillips head screws out, that hold filter frame in, remove filter frame. Next remove four front screws on drum alignment face plate. Set aside. Grasp drum and pull forward, off back guide rollers. Drum will drop down a little, reach in around drum and slide belt off. Remember to look in under drum to see proper placement of belt aroun motor shaft and idler pulley. Replace new belt around drum with ribs against drum. Route belt around motor shaft pulley, pull idler pulley toward motor and place belt around pulley smooth top runs against pulley. Reinstall everything you removed. Connect wires to door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Ashtabula, OH
- Parts Used:
- WP40113801
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Wouldn't dry---no heat
Disconnected the electricity,removed lower front panel with socket wrench and located high limit thermal fuse Removed wires and unscrewed old part and installed new thermal fuse. I reconnected the wires and it works perfectly.Also vacuumed out the lower area to remove unwanted lint while I was in this area. I saved a $75.00 service call by fixing it myself.
.
.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Milford, CT
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door was not catching. The female part to the door closing mechanism broke. It was such an easy fix! Took about 30 secs to fix!!
Pulled out the broken part than easily snapped the new part into place..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruth B from Hempstead, TX
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would not stay closed
I did a quick research online and found PartSelect to have the best price. I ordered my part on Monday 8/6 and to my tremendous surprise FedEx delivered it Tuesday 8/7!! I did not pay for overnight delivery. My son happened to come by that day and he took a small flathead screwdriver, pried the old one out and inserted the new part. Done in 5 minutes! PartSelect will be my supplier from now on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Riverside, CA
- Parts Used:
- WP40113801
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
No heat
Changed out the fuse. Didn t take care of the problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doug from Kearney, NE
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Latch was broken so door wouldn't close
This was real easy just slid the latch in front panel and attached to latch assembly to the door. The repair was about 45 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Webster, FL
- Parts Used:
- WPW10116735, WP40113801
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
dryer would not start
Began by unplugging power then removed the two screws from bottom access panel removed panel. Used a putty knife to push the release clips hold the top panel removed the two screws holding the front door and housing noted the three wires for the door switch removed those. Released the tension on the belt at the idler pulley lifted the drum assembly from the dryer. Tested the high limit fuse assembly with a volt ohm meter found no continuity indicating the fuse was blown. After reading the many other reviews I also test the high limit thermostat and found that it was not working as it should order bout parts and replaced all in reverse order plugged the unit back in and now have a working dryer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Kirkland, WA
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
latch broke
Replace with new latch.
Was this instruction helpful to you?
Thank you for voting!