AEM677W2 Speed Queen Dryer - Instructions

I removed the dryer front and the drum, then disconnected the wires from the dryer motor and removed it from the motor mount, after installing the new motor in the motor mount the rest was just putting the dryer back together the same way I took it apart, the best way to do this is to print out the diagram from partsselect.com and follow it step by step, this was so easy everybody can do this and save alot of money for the labor and the parts mark-up, try it you all can do it (SO EASY)

Removed the two sheet metall screws on the front foot panel, removed the four screws holding the door assembly, wrote down the wiring placement for the front door, removed the blower bulkhead assembly by removing one screw in the bottom of the dryer. Removed two screws and propped the dryer top panel up at a 45 degree angle to gain additional clearance. Removed the drum and belt from the front and back seals by applying simple outward pressure. Removed the screw in the bottom of the motor assembly allowing me to reposition the assembly for easy access. Removed bolt holding old Idler arm assembly. Assembled new Idler pulley referring to old assembly. Reversed the process to complete the repair. Note: I found it easier to simply hang the dryer belt over the dryer drum when replacing the drum in the dryer. First you need to place and align the drum then route the belt back to the moter pulley and then over the idler pulley. if you try to put the belt over the motor and then align the drum, it is difficult to keep the belt on the pulley. It might help to draw a diagram of the belt route or obtain the belt route diagram from the website for reference. Very easy job.

I removed the screws that hold the element in place. I disconnected the wires. I took the new part, which was easy to identify and order, assembled per instructions, and attached it to the wires in the dryer, then screwed it in. I normally let my husband do these repairs, but he wasn't available. It was easy and the dryer works perfectly again!

Remove front pannel
remove wires to light and switch
remove drum panel
disconnect motor wiring
unscrew motor mount
replace idlerlever replace belt reassemble all parts

I watched your videos - they're great! The strike was installed in less than a minute and voila - the dryer was as good as new!

1. Disconnect power and hose. Use a putty knife to release top of dryer. Two restraints couple inches in from each side on front. Raise top and do not remove. Block it up in vertical so it doesn't fly down to back.
2. Disconnect five wires at front. Use magic marker to mark re-installation instructions on underside of top.
2. Remove metal screws (2) that hold front to frame. Remove front.
3. Pull dryer forward and put cardboard box, or some such thing under back to support when laying dryer down.
4. Remove frame (4 screws) that supports filter assy and front of drum.
5. Remove belt. Mark assy. sequence on underside of top.
6. Remove drum.
7. Stand dryer back to upright position.
8. Disconnect spring from idler lever. Drop light may help here. Note position of lever for re-install of new.
9. Unscrew bolt that holds idler lever. Nut is on back of bracket. Must re-install this way as bolt has pivot surface for lever on front side.
10. Install new lever and reconnect spring.
11. Lay dryer back on box.
12. Put drum back in place. Insure it seats well all around the felt gasket. Any misalignment here and it will not rotate smoothly.
13. Put belt around drum using small pieces of tape to hold it into position around drum, and them depress the idler lever and install belt around motor pulley. Rotate drum to insure it rotates smoothly. Remove tape.
14. Re-install filter bracket and insure drum seats nicely in felt gasket. Again, rotate to insure smooth operation.
15. Pull dryer back to standing position and reinstall the front, and re-connect the wires.
16. Lower top and push down to reconnect locking devices.
17. Plug in dryer and turn on to see if all is well.
18. Re-install hose and start drying all those clothes.

removed lower front panel, two screws on bottom edge. Limit thermostat located on lower portion of vertical panel at rear of dryer. I was able to detach the two wires and removed the two thermostate retention screws with a nut driver. Since I could only operate with one hand, I taped the new thermostat in place lining up the screw holes in order to replace the two hex screws. reattached the two wires and front panel.

Open bottom panel and observed back left drum roller wheel wobbling and obviously making the loud rumbling banging sound. Search goggle for Amana model part -- found partsellect.com, and read the list of other DIYs:

Take off the lower and upper front panels (two screws
each);

Remove the front drum glide holder (four screws. Careful
here because of the two wires to be removed for
door open off switch;

Pulling drum forward only enough so the bad roller wheel
would come off shaft after removing shaft snap ring
keeper;

Grease new roller hole and old shaft then place the
new wheel roller on shaft;

Replace all items back after cleaning lent off.

Note: Snap ring was a bit tricky (need snap ring pliers)--make sure it is clipped back all the way on the shaft after new wheel is installed. Also, I thought it was a good idea to put something underneath the dryer drum to support it while it was slightly pulled out -- a block of wood, etc. I found a spot remover plastic bottle that wedged up to support the dryer drum enough to take pressure off the belt during wheel replacement.

first i checked the power supply then i checked each of the switches and limit fuses for continuity.
to do that i had to take the front of the drier off, four screws there. then i removed the bad limit switch 2 screws,the door switch was bad so i replaced it, no screws. since i had the front off the drier i removed the four screws that held the drum in place and replaced the belt. assembled the drier in reverse order when the parts came. 1/2hour total labor.

I inserted the clip

Remove the 2 screws at bottom of front panel, remove lower panel. Then remove the two screws at bottom of front door. Lift door forward so spring hooks can disengage from the top panel. remove door, disconnect the 5 wires to the door latch and light. remove the two screws at top of dryer to lift up top panel. Remove 4 screws at the front holding the drum. Disengage the belt from the tension pulley and remove drum. Replaced both roller wheels at the rear of the drum( one was broke). Then remove the screws (about 6 holding the plate in front of the blower wheel. Use a wrench to hold the nut at the back of the motor and a scocket wrench to remove blower wheel. (The Blower wheel was broken from the shaft and was spinning freely). Then do it all backwards to re assemble. i spent more time cleaning the lint from the inside than I took making the repair!

First I went to Maytag.com thinking it was best to go to the manufacturer for parts. Their search engine did not even recognize my part number. I tried every way I could think of. Then I just entered the model number in google and it sent me to the Partselect.com website. Diagrams came up and I chose parts from the pictures. The parts arrived in about 3 or 4 days and fit perfectly.

Replaced the recommended drum rollers, belt and tensioner, light bulb. Found repair manual online (bit of a hunt)made job easier still took 2.5 hrs. Then turned drum by hand no squeak. Turned it on and still squeaked. Isolated to motor. Replaced it (had to take dryer completely apart again but went quicker due to experience also had to disassemble the motor assy and rebuild. Took 1.5 hrs works like new now. The design of the dryer is not bad remove bottom front panel first, screws at very bottom of panel then two more screws are uncovered to remove front. It just lifts up and pulls out. then remove four bolts which hold front frame on (supports drum) all this has to be done to reach the replacement parts. drum wheels are held on by snap rings not the screws (real fun if you take them out) reverse to reassemble.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

1-Unplugged drier
2-removed lower panel-(2)-8mm screws
3-removed intake from fan-(3)-8mm screws
4-removed dryer's front panel-w/door assembly-(2)-8mm screws. (note there is a door switch you will need to disconnect the wires and remember which terminals they go to.
5-remove the front drum support-(4)-8mm screws
***** at this point the drum is exposed *****
6-reached under the drum pulled the tensioner to relieve tension on belt, then dismounted the belt from only the tensioner and motor shaft; leave the belt on the drum!
7-pull drum toward you and forward about 3-to-4 inches, this exposes the drum rollers.
8-use a screwdriver and pry-off the retaining clip on the end of the roller's shaft and remove the roller.
9-remove the roller support-(2)-8mm screws
10- reinstall new roller support
11- apply a light coat of disc-brake hi-temp wheel bearing grease to the roller support shaft, very light!
12-install a new wavy thrust washer, new roller(note they will say "front" on the side that should face you. Don't mount it backwards!
13-install the outer thrust washer and the new retaining clip; use a flashlight for this part!
14-repeat for the other drum roller.
**** while you have it apart use a vacuum to remove lint from every where you see it; it is a fire hazard!
**** if you think you need a drive belt now is the best time to change it *****
15- re-assemble the dryer in the reverse order, don't forget to re-install the drive belt and be careful not to pinch the door switch wires.
16-re-plug the drier and test