Models > AEM677W2

AEM677W2 Speed Queen Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for AEM677W2

Viewing 13 of 13
Keep searches simple, eg. "belt" or "pump".
If your dryer is not tumbling, takes a long time to dry, or is noisy while tumbling, it may be time to replace the drum support rollers. These hold the drum in place while it rotates, so if they have ...
In Stock
The multi rib belt, which may also be called a dryer drum belt or a multi-v belt, helps to rotate the drum of the dryer. The belt wraps completely around the drum, around a tension pulley, and then ar...
In Stock
$14.16
Located in the front bulkhead of your dryer are two drum glides, which help to ensure that the drum rotates smoothly and quietly while the dryer is operating. When the glides wear down, it can cause a...
In Stock
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
In Stock
This washer is 3/4 inches in diameter.
In Stock
Meant as a backup to a high limit thermostat, this fuse is typically set to trip at a higher temperature than that of a high limit thermostat. This is a one-time use fuse, so when it does trip, you do...
In Stock
This kit comes in two pieces: the catch and the clip.
In Stock
The spring for this part is sold separately. This idler assembly is for dryers. Idler assembly includes the idler arm and the idler pulley that maintains tension on the drive belt, allowing the ...
In Stock
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
In Stock
This part replaces older two terminal switches.
In Stock
This part is located between the back of the drum and the rear dryer panel.
In Stock
This dryer drum glide pad is an inch long. It is made of a felt material and is used for gas and electric clothes dryers.
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for AEM677W2

Viewing 10 of 10
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Too hot
Fixed by these parts
Fixing Fixing
How to fix it
Drum Not Spinning
Fixed by these parts
Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing
How to fix it
Won’t Start
Fixed by these parts
Fixing
How to fix it
Not Heating
Fixed by these parts
Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Chris from Hopedale, MA
Parts Used:
WP37001042, WP233520
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Drum not centered , clothes getting stuck in dryer
The first thing I did was to unplug the dryer from the wall. Then I removed the bottom two screws and slid the bottom cover off so i could see all the way to the back, I tipped the dryer back against the wall and searched for the problem with a flashlight. I noticed that one of the guide wheels that held the drum in place was sheared of f. I took the new drum support roller out and carefully slid it over the shaft, I had to jiggle it around for a bit, but then it finally was seated correctly. I replaced the washer and then the clip using a pair of needle nose pliers and a regular screw driver and then turned the dryer by hand to see if the wheel came off. After confirming that it worked, I put the cover back on, and plugged it in and tested it.
525 of 548 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Steven from Holderness, NH
Parts Used:
WP40113601, WP37001287, WP37001042, WP500121
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Squeeling and grinding noise
Wasn't the belt!! Changed it anyway. Should have come here earlier. That mistake added several days to the repair waiting for a second batch of the right parts. Became a pro at taking the dryer apart and reassembling, though! Easy job, just take your time and mark your wires, if you need to.
Followed other people's excellent instru ctions. Clean out all the dust bunnies. Schematics were a great resource. Those and the prices made me a repeat customer.
The shaft of the Idler Lever wheel was the cause, but decided, since I had it apart, to spend a little more money and replace both Drum Support Rollers and the Roller Bracket and Shaft Assembly. They showed some wear, and the parts were very inexpensive. Make sure you have snap ring pliers with prongs that are smaller than the standard 0.40 to save some aggravation with the Drum Rollers. $5 tool. Total parts were less than $60. Probably saved $150+ in labor. Quieter than ever now. Thanks!
482 of 497 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Skokie, IL
Parts Used:
WP40111201
Difficulty Level:
Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.)
304 of 354 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!