MDE3000AZA Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Larry from Swanton, OH
- Parts Used:
- WP303396
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Dryer ran hot
Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- matthew from Central Islip, NY
- Parts Used:
- WP33001762
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
no heat, coil wasnt getting hot
took old one out then i had to strip the connector off new one was to big...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from Lilburn, GA
- Parts Used:
- WP33001762, WP307178, WP303396
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
Dryer wasn't heating sufficiently/consistently.
Removed front cover, removed old heating unit, installed new thermostat,heating coil inside the dryer and finally replaced the fuse in the front. The main complication was reaching the screws for the heating coil, not really complex.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from CAMBRIDGE, MN
- Parts Used:
- WP33001762, W10169313
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Will not start all lights on,makes a ping sound on the control panel when you push the start button
Replaced thermal fuse and replaced door switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- keith from saluda, VA
- Parts Used:
- 33001809
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Dryer continuously running, no timer advance, dampness indication stayed on "wet"
Took 3 screws out of the back of the back of the machine and tilted the control panel houseing forward. Slid the module free of it's track and unplugged the bundled wiring plug. Plugged new module, relpaced in is slot and put the control panel back in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Town Creek, AL
- Parts Used:
- WPY308612
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
An underwire form a bra shorted the element burning it out
Knowing most mfgs. put prints under the conturo panal we started there.
Diagonstics required a multi meter.
The part was removed and the internet serched.
My local parts center was more expensive and would have to order the part. I called Partselect
found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.
Diagonstics required a multi meter.
The part was removed and the internet serched.
My local parts center was more expensive and would have to order the part. I called Partselect
found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- claude from laguna niguel, CA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
missing, probably broken female latch part
Press in the new female latch part with thumbs. Took about two seconds!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Bellevue, WA
- Parts Used:
- WP33002535, W10410997, WP33001807, 12001541
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Motor burnt a phase
If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.
My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.
I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.
My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.
I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- karl from monroe, GA
- Parts Used:
- 306436
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stay closed.
I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Menomonee Falls, WI
- Parts Used:
- WP33001808, 33001799
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
rodent entry through vent,chewed parts,(distroyed).
Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Loganton, PA
- Parts Used:
- WP307178
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Heating Element was starting to fail
It was very simple. I removed the fromt cover on the dryer. The heating element was easy to get to and after removing all the attached wires and 4 nuts. The new element was installed, reattached the wire correctly and put the screws back in place. It was extremely easy to complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RODNEY from Spokane, WA
- Parts Used:
- WP6-3129480, 33001801
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Terrible sqeel as dryer rotated.
A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hazel from CONNERSVILLE, IN
- Parts Used:
- 12001541
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
noisy
I watched the video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thurman from Huntsville, AL
- Parts Used:
- WP6-3705180, WP6-3700340
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Squeaking noise while spinning
removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tara from North Canton, OH
- Parts Used:
- LA-1003
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Female End Of The Door Catch Broke
First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--
Was this instruction helpful to you?
Thank you for voting!