MGDB950YG2 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Scott from WOODBURY, MN
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
lint screen was not catching lint and sending out the dryer vent
replaced dryer lint screen with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglass from Madison, IN
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The door catch no longer held the door shut. It would not grip the bayonet.
The only challenging part was getting the old catch out. It can easily fall inside the door, not that this is really a problem, just leave it there. Using pliers get a good grip on the edge of the old catch and rock the top out, then pull to get the bottom out. There will now be an open hole. Align the new part with the open hole, and simply push it in. It will catch, and click into place. No tools are needed to install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from LINCOLN, NE
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The Dryer door catch broke and the door would not latch.
I removed the broken door catch with a screw driver. I then used a pair of pliers to push the new door catch in place. It was an easy repair and saved me quite a bit of money.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie from BEND, OR
- Parts Used:
- 49621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling feet on dryer.
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from MARION, KY
- Parts Used:
- WPW10359272
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Socket set
Rollers making a noise.
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from CAMARILLO, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Dryer was making noise - thought it was the belt, turned out to be the tensioner.
I followed the video provided by ‘Partselect’; although it was not the exact model it was close enough to get the job done with high confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from FRANKLIN, MA
- Parts Used:
- WPW10314173, WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Door would not close after I slammed it.
Simple with the Instructions in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from DINUBA, CA
- Parts Used:
- 4392067
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Repair video made it easy
Just follow the repair video, it was easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allen from KENNETT, MO
- Parts Used:
- WP8577274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Shutting off and had to wait before could turn back on
Followed online video very easy and dryer works like new one....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from ETTERS, PA
- Parts Used:
- WP8544737
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
The fan wheel had a blade break off, my bad.
I went on the site and found the part I needed and then watched the video explaining how to dismantle, replace the part, and put the dryer back together. It was easy, especially with the video instructions.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from CARY, NC
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The lint filter needed replacement due to what is probably normal wear and tear.
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Canyon Country, CA
- Parts Used:
- 279311
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench set
The dryer would not heat up
I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rory from LEESBURG, VA
- Parts Used:
- WP8577274
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Dryer kept throwing the E1 error indicating the thermistor needed replacement
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back in, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cindy from BENZONIA, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Screen ripped
Dropped new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from FORSYTH, MO
- Parts Used:
- WPW10111905
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
door catch broken and fell into door
snapped new catch into door
Was this instruction helpful to you?
Thank you for voting!