MDG7658BWQ Maytag Dryer - Instructions

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

removed the timer knob from the panel(pop off the grey knob cover and the knob comes right off) remove three torx screws from the top of control panel and tilt the panel forward.Slide the timer assembly to the right(there is a lock tab you have to push down) and unplug the timer.Reverse procedure and reassemble.That was it.

Press in the new female latch part with thumbs. Took about two seconds!

Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

By following the directions included with the kit it was fairly clear. The diagrams of the control valve was helpful. It would have helped to tell which screws to remove to access the valve and where the screw was that retained the burner assembly.

I watched the video

First changed the ignitor, which did not fix the problem. Unpug Dryer. Removed the front panel by taking out the 2 phillips screws and pulling the bottom of the panel out first, releasing the top clips. Remove the clip holding the coils on and replace them. Plugs just pull off, each are different so cn't mix them up. Both sensor and thermostat are pretty easy to get to using 1/4" drive socket. the screws can be a bit tough to get back in, but be patient. Wiring is pretty straight forward, remove from the old part and put on the new, same orientation. This is a good time to vacuum out the bottom of the dryer to get any loose lint out. Return the front panel, tilting out at the bottom to engage the top clips. Plugged it in and worked like a charm

I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (and the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.

First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i decided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

Removed four philips screws, two holding door on and two on opposite side of door in order to remove front cover. Then removed two 5/16 screws holding clips that lock the top cover down. Then the top cover hinges up with open access to the drum. The baffles are held into place with two #10 x 1 1/4" screws with 5/16" head each. These had pulled through the drum. Installed new baffles (do NOT come with screws / you'll have to buy some). Had to put small washers (also had to buy) on the screws to hold it onto the drum since the other screw heads pulled through the drum. Closed lid, installed retaining clips, installed door onto frame, installed front cover around door, then screwed door hinges into front cover and screws to other side. Took about as long to write these directions as it did to actually do the work... EASY job!!

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.