MLE15MNAGW Maytag Dryer - Instructions

Followed the directions of the video and all went smooth. Cleaning the lint and parts was the more time consuming than the actual repair. 30 minutes for the repair and an hour for the clean. All and all very easy.

Was extrememly simple. Just unscrewed the two screws at the bottom front of the dryer and pulled the front of the drayer out. PUshed the broken catch out and snapped the new catch in place. Reattached the dryer front with the two screws and was done. Less than 15 minutes.

Removed the door then removed front panel then removed 8 screws that held the drum in. At this point reached in and removed the snap ring on the wheels and replaced the washers and wheels. Then reassembled it.

i took off the door and the front of the drum and removed the drum. I removed the locking clip from idler pully and replaced and lubricated the shaft and slid the new idler pully on. I hung the belt over the back and put the drum back in and aligned the belt and turned by hand to get the belt in the correct position. Belt came off a couple of times because i think the belt was twisted. installed the front panel and the door, plugged the cord in and started it up and it was perfect.

First I removed the two screws on the front panel that hold the element in place. I then pulled the element out about 3" and disconnected the two wires. Find out the roller broken. Place an order with Partselect from friend recommendation. Fast delivery, replace the broken roller, reverse the process and test the sound of the dryer. Very satisfied with the parts. Thanks!

First thing to do. . . . Unplug the machine. After that, remove the top 2 screws from the cover from between the washing machine and the dryer and remove cover. Then remove the 2 screws from the top of the front dryer cabinet, pull front cover out slightly and gently let it lay forward. From this point, you can look in and see the drum rollers. Behind the rollers on the roller shaft is a 1/2" nut. Use a 1/2" gearwrench to remove the nut, and pull the shaft with roller attached out forward. Use snap ring pliers to remove snap ring, take off old roller with bushings, and replace with new. To re-install shaft with new roller, you will have to lift the drum slightly to give yourself enough room. Re-assemble the front of machine (note: be careful of the wiring on the control panel, as some connectors may have pulled loose. Make sure they are all connected before replacing front of machine). Plug machine in and test it out. While you have the machine open, use a good vacuum cleaner and remove the lint that you will find inside the machine. Depending on how old the machine is, you should find quite a bit.

Remove the door and front cover ,then the top flips up ,remove the front drum support then the drum,remove the snap ring and the pulley

followed instructions on youtube. The only hitch was threading drive belt back on. the video showed from back instead of front.After I was done I noticed an access door in back that would have helped.

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

first, i removed two screws at the bottom of front panel. then lifted from the bottom removing it. next, removed drum surround and drum. next , removed right roller and roller shaft. then installed new shaft, slide roller back on shaft. next reinstalled drum, drum surround and front panel. Now so quiet you can hardly hear it run, also my sister says it drys much faster.

I followed the YouTube video for pulling the heating element to remove and place the thermostat. The actual thermostat removal and replacement was pretty simple. Most of my time was spent removing the front panel, pulling and reinstalling the heating element.

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

I followed the video instructions which were excellent. Dryer repair was a cinch.

I use U Tube watched Video, you have to take apart the dryer, but pretty simple to do. The drum rollers were very easy to install, make sure to have snap ring plyers, installing belt was easy too, make sure to put it back on it the way it came off, mine was ribbed side down on drum. Take a picture if necessary. Getting the belt on the pulley right is the most important part, the rest is just reassembling,