MLE15MNAGW Maytag Dryer - Instructions

Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.

take screws out of front of dryer, pull front off to expose drum and replace baffle

There are several parts that will cause the dryer to squeak, drum roller, idler pully and the drum slides. To start, remove the door and the two opposite screws. Pull the front cover down and remove, no screws to remove, this is a snaped on piece. Next, remove the two screws holding the dryer top bracket and lift the top. Take drum support by removing the screws and then remove the belt from the motor and remove the drum. The hardest part was removing the C clips from the roller axle even with the snap ring pliers. Replace the drum rollers and reverse the process to re-assemble. Of course, the rollers weren't the problem even though they were worn out from 20 years of service. I ended up replacing the idler pully and and the idler pully support arm. If I had all of the parts prior to starting, the total time would have been about an hour. I did watch several YouTube videos before attempting the repair. That helped me understand the "how" and made it easy once I started the repair.

I followed the Part Select tutorial on Instant Repairman and retrieved the missing screws at the base of the dryer as described in the tutorial and after trying to reassemble the original baffle notice the baffle screw holes were stripped. I decided to fill the holes with a strong glue before reinserting the screw to temporarily keep the machine running until the new baffle arrived as it was just ordered the night before. When the new baffle arrived I decided to hold onto it as a spare if or when the original baffle broke off again.

Followed instruction video

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

I looked on line and found a scematic from your web site to determine how to dismantel the dryer. Once I was inside I was able to determine that the drum roller was making the noise. I decided to replace the other moving part while I was inside just in case. . . Pretty easy job

Removed front panel and tumbler, replaced roller axle,
wheel, and front glides. Anybody can do this.

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

Removed power and front panel, removed broken latch, pushed in new latch and replaced the front panel and power. Done

We could not find directions for the brand that we have. First we took the back off, which we did not need to do.
lift the top of the dryer, remove the front remove drum. Place belt on front of motor, wrap double belt around support on bottom of dryer, open the remaining belt and stretch around drum. Hold drum in place, replace front and top.
Need at least 2 people, not at all intuitive.

Unscrewed door and front panel. Pulled and took the, off. Used standing flashlight to illuminate the area underneath the dryer barrel. Tried various tools to take out broken plastic remnants. Then, used small electric nutdriver to screw the tall baffle into place with newly purchased metal screws. Was a bit hard to reach and tight but finally worked once I found an appropriate tool and top.

The video was excellent and made for an easy repair. Would highly recommend.

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

First removed front door 2 screws holding it to frame, then removed 2 screws holding front cover panel on tilt out front panel, used vac to clean inside, removed idler arm with pully attached, replaced with new parts when I did a test run still had a llitle squeek, the drum support wheel on right looking from front making some squeeking,I went back in removed part shaft had small rust spot cleaned with jewelers cloth lubed and wiped off, no more squeek I wish I had ordered new drum wheel when I ordered idler parts, then I could have done a complete overhaul now I know more I have never worked on a dryer before the drawings on the web site heleped a lot