MLG23PDFGW Maytag Dryer - Instructions

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

Others have described how to remove 4 screws and remove the front panel of the dryer. The problem I saw is that some screws broke off and fell inside while others remained on the separated baffle. The old screws that I found were 1 1/4 inch. The parts manual indicates a replacement screw that is 1 inch long and a number 10 width. One set of holes for the baffles has slotted holes. It appears that wear in the paint indicates movement before breaking off. My solution to the slotted holes was to use washers on the screws and to tighten the screws in the position where any force was not going to move the screws to the center position of the slots. The force of the separation caused the slotted holes to expand.

I removed the dryer door and attaching hardware to other covers. Raise the top cover and prop it up. Remove the drum retaining cover and disconnect the door switch wires, making note of their locations. Release tension on idler and take belt off of motor. Pull the drum out with belt still around it. Vacuum lint and dust from inside cabinet. Use snapring pliers and remove the snaprings on the drum rollers. Remove the old rollers and washers, clean the shafts and apply a light film of oil on the shafts. Install new rollers and plastic washers on shafts and secure with snaprings. Remove the "E" clip from the idler shaft and remove the old roller. Clean and lube the shaft and install the new idler and clip. Place the new belt on the drum with the ribs against the drum. Put the drum in place and install the front drum retainer. Position the belt around the motor pully and tensioner. Rotate the drum to get the belt to track. Attach the remaining covers.

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

As the dryer would be going you could hear a grinding noise every other sec or so, like sandpaper sanding metal.

Disassemble as per video on this site and install replacement felt seal.

Took a bit to tear down and change and reassemble but well worth the time as there is
no one in our area that does this type of repair(s) any longer

Moved the front door/panel two screws at the bottom of the panel.Then removed the front plate and support for the drum assy. four screws.Then loosen the belt and removed the drum assy. to get access to the drum roller to the back top right,.Used snap ring pliers to remove the clip cleaned the shaft an installed the new roller with the fiber washers and installed per instruction from your video,Also replaced the belt and put all items back in reverse order.It worked like a champ so easy,I would recommend your web site and videos to any one who wants to do it yourself. I have used you in the past and will continue using you for other items for parts and support.

i took off the door and the front of the drum and removed the drum. I removed the locking clip from idler pully and replaced and lubricated the shaft and slid the new idler pully on. I hung the belt over the back and put the drum back in and aligned the belt and turned by hand to get the belt in the correct position. Belt came off a couple of times because i think the belt was twisted. installed the front panel and the door, plugged the cord in and started it up and it was perfect.

Followed the video. Hardest part was getting the belt around the ideler pulley and motor pulley without seeing. But I got it! Thanks to this site you rock!

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

followed instructions on youtube. The only hitch was threading drive belt back on. the video showed from back instead of front.After I was done I noticed an access door in back that would have helped.

I use U Tube watched Video, you have to take apart the dryer, but pretty simple to do. The drum rollers were very easy to install, make sure to have snap ring plyers, installing belt was easy too, make sure to put it back on it the way it came off, mine was ribbed side down on drum. Take a picture if necessary. Getting the belt on the pulley right is the most important part, the rest is just reassembling,

I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

The video from this site is perfect. Unplug dryer, remove front panel, unclip wires, remove next panel and pull the drum out. Replace drum support wheels using snap ring pliers (buy the pliers with changeable tips because the holes in the snap ring were pretty small on mine). Put it all back together. The trickiest part is getting the belt back on...just be sure it's not in the groove around the drum and pay attention to how to get it on the motor wheels. Good luck!