BDG810 Maytag Dryer - Instructions

Took 2 screws out of the bottom of the dryer so the front face plate came off. This allowed access to the door latch catch, which was easy to pull out with pliers. Pushed in new latch catch until it "popped" into place. Easy, easy, easy!

It was so easy to repair that my wife did it. She used a screw driver to pop out the old, worn plastic part that the door latch goes into and snapped in the new part and it was all done. So nice to be able to fix it yourself!

The dryer door on my mom's Maytag SG1000 (washer/dryer stacked unit) wouldn't stay closed; the latch had finally broken. The replacement kit includes both the female latch and the male striker. I replaced both even though the old striker was still good. The old parts were easily pried out and removed with a small flat-blade screwdriver. But what the PartSelect website, and the other "repair stories" found here, fail to mention is that the male striker is held in place with a small metal "door strike retainer" plate that falls down into the door as soon as you pry off the striker. You will need a small Phillips screwdriver to take the door apart and retrieve the plate. After snapping the new striker into the plate the door can be reassembled -- a simple job that only takes a couple of minutes.

Only needed half the parts. Installed the catch for the door and saved the other part.

Pop out with screwdriver and push in new part. easy

unscrew the screws at bottom front of dryer, lift outward, upward, the bottom of the front of the dryer. As the dryer front tilts outward/upward from the bottom, the area where its hinged at the top of the front will disengage from the main frame of the dryer and the face of the front of the dryer comes off. remove the old door latch by manipulating the plastic body of the latch (wiggle, twist pinch . . .) until, from the back, you can push the old latch forward through the front of the front of the dryer. At this point, you can put the new door latch back in from the front and push it in to place.

Replaced the Latch

I followed the video on the site which was really helpful.I took the door off without problem. I had to take the bottom panel off the front and unscrew screws on large front panel.Replacing the latch was a breeze. Just as shown on video. Be careful that dryer drum doesn't fall down off wheels. My did and had to push it back up.Replaced all panels and screws and it works great.

The instructions that accompanied the part was extremely helpful. I removed two screws, lifted off the front panel, used the pliers to remove the old latch, pushed the new latch into the hole. I then replaced the panel (The part that is attached to the door was not broken). I tightened the two screws and the job was complete. I saved a very expensive service call. :)

First - I did some research on line as to the possible problem with this dryer.
I had already taken the front apart before, so I knew what was needed to remove the door and front.
Remove the 2 screws that hold the dryer door in place with a Phillips screwdriver. Remove the two screws on the opposite side of the door also. Place the door out of the way. The front panel of the dryer now tilts forward. The front panel sits on two clips, tilt forward and lift out of place. The door switch has two prongs that hold it in place, pinch the prongs and the switch slides out. Disconnect the two wires on the switch and connect the wires to the new switch. The new switch slides into place. I tested the new switch before I put it all back together. Took me no longer than 15 minutes.

Just used a needle nose plier to remove the broken part, and inserted by hand the new part.

Saved a lot of time by just using needle nose pliers to break the receiving end of latch off of the front of the dryer. No big deal if parts fall Inside, won't hurt anything. Then just pressed new part into front of dryer. No need to remove front dryer panel.latch piece on door was not broken so I left it alone. Took all of about 2 minutes.

I entered the model number and make of the dryer, selected the door latch part and ordered. My order had a link to a video that explained installation. It was pretty easy, and I am a girl :)

Pried out the old female hold and snapped in the new one.

1.Separate the inner and outer door panels. Install the new latch thru the backer plate. 2. Remove the front panel to access the door catch. Remove the existing catch and replace.