HYE3658AZW Maytag Dryer - Instructions

I just followed your video how to replace a broken belt , after viewing replacing belt went easy

watched your video on 'how to' and did it like man showed..no problem

Easy repair and I am not the handyman type. Unplug the unit. Lift the top. Remove 2 wires from temperature sensor and remove single screw to lift out the plate the sensor is mounted to(Easier to change the sensor out this way). Remove 2 wires from heating element and then remove single screw. Lift out heating element and replace with new one. Screw back in and reattach 2 wires. Remove 2 screws on the plate for the temeperature sensor and replace with the new sensor. Once 2 screws are back in the plate holding the sensor, screw back in with single screw and attach 2 wires. I called a tech and they wanted $125 just to look at the unit. When I read other reviews of how easy this repair was, I thought it was worth a try. Definitely saved us a bunch of money and time.

Grown daughter did the repair following instructions on your site........Unplug, take screws out of top by lint filter and with putty knife pry up top panel and lean back. Unplug elec. harness in front corner. A screw on each side of front panel removes that. Get old belt off and then we vaccumed all the lint from under and around drum. Put new belt around drum making sure not twisted and pull pulley as shown to make tight......... would have taken less time but we vaccumed all the lint from under and around the drum. Anyone could do this......

Open the top of the dryer, thermostat can be plainly seen. this one was obviously fried, made it easy to determine cause of problem. remove old thermostat, pins pull off posts, using socket take off nuts (hang on to the nuts), put the new on. Fixed.

Once we realized we needed to take the FRONT off the dryer, not the back all went well. It was an easy fix and the part fix perfectly. Instead of $60 or more for a repairman, we spent less than $20 fixing the dryer.

the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.

This is the second time that this has happened with my dryer. The first time I replaced the thermostat and fuse, and it worked for a few years. This time I replaced the element and thermostat at first. Still nothing, then got the fuse; and walla just like new. Of course I lost a screw somewhere down at the bottom of the dryer, so there is only one holding the thermostat in place. Also I took off the front and cleaned out the lint traps; both times it was loaded with crap. Probably why it stopped in the first place.

Had a problem holding drum in place and putting front back on. Got it together and drum wouldn't turn. Had to tear it a part again and belt had turned.

Very difficult for one person, trying to get the belt engaged into the motor pulley and the idler pulley at the same time. Trying to overcome the tension of the heavy spring on the idler was the main problem, while coping with the small working space with the drum in place. Solved all the problems by removing the drum (for the 3rd time) and making a piece of wood to wedge in against the outside wall of the machine to hold back the spring loaded idler. Then slipped the drum back in place and gently slid the belt around the drum. Then reached in under the drum and slipped the wood piece out while making sure the belt remained on the pulleys. If I had the wood idea at the start, it would have been about a half hour job. Good luck, and don't pinch your fingers.

I pulled front off drier old wheel was easily removed because it was broke in half. New wheel fit tight and took a little effort to get new wheel installed. Installed retaining clamp to shaft and vacuumed out lint before putting front back on.

Lifted top lid of cabinet using putty knife to release clips then removed front panel. Removed drum from unit and set aside. Found that one of the drum support roller wheels had lost the rubber roller. Removed old roller and secured new one which was an easy fix.
Installing the drum belt was a bit more difficult as I had to do it alone. I threaded the belt through the pulley/control arm and held it taugt with one hand and then inched the belt around the drum while holding it in place with my knees. Took awhile but I got it secured. Would definitely help to remove one of the side panels of dryer or have someone assist you.

Released lid clips, two screws removed to remove the front. Took tension off of the belt by removing it from roller, then lifting tension spring from base. Removed drum to gain full access to motor. Lubricated rollers, vacuumed all areas to remove lint. Replaced motor and belt. Re-installed drum and re-attached tension spring, dryer face, and top. Works fantastic. Hard part was getting spring released and reattached due to location.

This is a very easy, no frills dryer to work on. Access to the blower by removing two screws holding the front panel. Blower fan held in place with a snap ring. Just recently replaced the drum rollers and shafts and the belt as well. It ran sweet for about a week and then an electric control on the motor went bad and it on;y can be replaced by buyig a new motor at $135.00. Some luck huh? Found a guy local selling a 8th month old Maytag of higher capacity and more bells and whistles for $150.00. It works great and my old Admiral uses many of the same parts so I'll have a supply of thermostats, rollers, etc., when the Maytag goes on the blink.

Vacuum out the dryer vent & trap of all the tenant's sleeping bag stuffing, intall the new lint trap and Voila! It works again.