HYE3658AZW Maytag Dryer - Instructions

Item # PS11740721 motor drive pulley. This has a 3/8-24 reverse thread inner bore. Fit my Maytag model MDE508DAYW dryer made by Whirlpool, with drive motor on the lower right below the counterclockwise rotating drum and exhaust blower at the front of the machine. It might work with a number of brands of dryers made by Whirlpool with that configuration. Check the motor shaft thread and the drive belt which is a 5 rib belt 5/16ths inch or 8 mm wide. For Joe Blow the local appliance repair places only quote replacing the motor and pulley as a unit. At $170.

Opened up every panel EXCEPT the front, then discovered how easy that is. Replacement belt was a snap to install. I noticed some plastic collar thing on the driveshaft appeared to have melted. Did not appear to be critical part, so I put it together and tested it out. Seems to work fine. I think the collar is there to prevent the belt from potentially slipping off the driveshaft.

I popped the top off and tipped the dry over . It took 2 to reposition the drum and belt back after taking it out and remving the old wheel and replacing it.

My part came a day or so after the order was placed. There was really no installation required, but I will definitly make orders from this site again. Thank you very much!

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

I just used screw driver to pop of clip put new roller on poped clip back on

Very simple-remove 3 screws that hold the Control Panel on, remove the two connectors and replace with new part in reverse order. Unfortunately, this did not fix the problem. Will be ordering complete timer assembly.

googled"dryer not heating". landed on partsselect.com. checked parts like website said with multimeter. pointed to thermostat. ordered it, replaced it, it works now.

removed the lens cover, replaced the bulb and reinstalled the lens cover.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I took the front off the cabinet (pry up front of top and remove two screws. Removed the drum, replaced the left rear drum support roller by removing one snap ring on shaft of roller and repacing after installing the new wheel. Reinstalled the drum, the hardest part of the repair was getting the belt back on the drum. It is hard to reach the belt to place it back on the motor. (small space to reach through) Being able to purchase a single wheel from this website saved me $50.00, the local suppier wanted to sell me a whole kit.

It was easy. Just removed the old seal and plugged the new one in place. Took less than 3 minutes

Received the replacement filter which was an exact duplicate of the 22 year old filter. Took the old one out; slid the new one in and got ready for another 22 years of use. At 86 years of age I probably won't be around to see the new filter wear out. The dryer has already outlasted the place where I purchased it - Montgomery Wards! They just don't make stuff to last like this anymore.

Looked up dryer by serial number on the internet. Watched the video on the website very easy installation. Ordered the part it came in within 2 days. Opened the top of the dryer with a 10 in one tool (like a putty knife). Took out the out defective parts by unscrewing the thermostat took wires off the old part and put them on the new part not to confuse wires. Did the same with the heater element installed the new parts. Very simple. If I had to call a repair person it would have cost 3 times as much as the part alone.

First I removed the screws of the dryer cover. Next removed the screws holding the dryer drum.

Drilled out the two rivets left from the old glide. Inserted the plastic and postitioned the cushion underneath. Inserted the new glide and drilled a hole in the plastic to accomodate the new rivet. Inserted rivet. Pulled the other end so it was tight holding the cushion and did the other end. Done.

Had to cut the glide 1/4 '' of the width to slide it through the existing slots in the panel.