HYE3658AZW Maytag Dryer - Instructions

First unplug the machine and turn off the gas. Then, I pried the top up (2 clamps on front, 2 screws to the lint screen). Then I removed 2 5/16 nuts that fastened front panel to sides. I held the drum and pried the front panel back while my wife slipped the new belt around the drum. Then, I buttoned everything back up in reverse order, removed the kick panel, threaded the belt through the tensioner pulley and around the motor shaft. It's really that easy. PartSelect.com makes it simple with quick, accurate service.

Took two screws out of the Lint tray on top. remove to bolts from under hood then put new belt on. Always make sure there are no twists in belt when put back on

Once I realized it was just a drum belt and how easy it was to fix, I ordered the belt myself with no help from a national warehouse hardware chain where the manager said "I don't have a belt but I can sell you a dryer." Thank you I kept my 300+ dollars and once I got the belt it only required removing the two screws that sealed the lint screen cannel to the top; popping the top, removing the to nutbolts fastening the front to the side panels; slidding the front panel out; putting the belt around the drum and attaching it properly to the tension pully and motor. Finally, I closed it up and tested it. Household hero in less than 12 minutes! Not bad for a psychologist, eh?

Watched the video on the site and it was spot-on! Super-easy, took like 10 minutes to replace the belt. Thanks!

I tilted the unit back enough to scew the new legs into the threaded holes.

Disconnect power. Removed front panel and lifted top. Removed belt around spring pully and motor assembly. Carefully eased belt around back of drum and gasket. Reverse process.

Just slid the new filter in.

Watched a video and went to town taking it apart. I stuck a pop can under the barrel to hold it up while I worked on pulleys. My dryer does not have a plastic pulley but a metal tension bar with a hole in the middle. Ran upstairs and watched a different video with my set up and all was good. 5 min of work 5 min watching Youtube and 5 min cleaning all the lint out of the machine. I am actually glad the old belt broke because some of the lint was in a clump and had scorch marks on it. I took the shop vac to every part of the cabinet and shoved it down the lint trap sleeve also.

First off, the hub is a tight fit. If the fan barely fits the shaft, but doesn't go on all the way, do not try to enlarge the hub. Lightly lubricated the motor shaft and the inside of the new factory correct fan wheel with a small amount of very soapy water or similar lube.
Then placed a socket against the face of plastic hub and LIGHTLY tapped fan wheel into place until fully seated.
Install the old retaining clip.
That's it.

DISCONNECT THE POWER. Double check the dryer is unplugged. Use a putty knife to free the latches holding the top of the dryer in place. Lift up the top of the dryer and secure it in place (be sure it's safely held open and won't come crashing down onto yourself as you work). Remove the two screws on the inside and near the top of the dryer, which hold the front and side panels. Gently lift up on the front panel (it may help to open the dryer door to get a better grip). Once free from the bottom clips, carefully rotate the front panel so that the door sensor wires are not strained. Once the front panel is out of the way, grab the drum and firmly lift it up and away from the back. (The drum has rollers and ridges at the rear and you'll need to pull the drum out of its "track"). Slide the new belt around the drum and position the drum about halfway inside the dryer. Loop the belt around the motor, but not the tensioner, (it will be easier to install the drum if you wait to tension the belt). With the belt around the motor, gently slide the drum back keeping the belt around the motor pulley. Press and guide the drum back onto the rollers at the rear. Check the belt is positioned correctly around the drum and motor. Reach back from the front and loop the belt around the tensioner. Rotate the drum by hand and make sure the belt is aligned and the drum spins smoothly. Position the front panel and slide it onto the lower clips. Install the screws being very careful not to drop them into the abyss... Close the lid and plug in the power.

Tools and materials:

#2 Philips head screw driver
Standard flat-tip screw driver
1/4" nut driver or ratchet
1/4" drive sockets: 1/4, 5/16
Something 3-4 inches thick to wedge under drum for support (i.e. scrap 4x4, soap bottle, books)

Replacement Procedures:

1. Unplug dryer from wall outlet
2. Pull out lint screen
3. Remove 2 Philips screws attaching lint trap to dryer top
4. Lift hinged dryer top panel near front and lean it back on wall. You may need to pry between side panels and top with flat-tip screw driver to get it started.
5. Disconnect plug from dryer door switch near front
6. Remove two 1/4" and two 5/16" hex screws inside front panel near top.
7. Open dryer door and lift front panel straight up to disengage tabs from slots near bottom of front panel.
8. While supporting drum with one hand, lift front panel and set aside with other hand.
9. Slip replacement belt around drum with ribs facing drum and position it where old belt left its mark.
10. Wedge something under drum to support it while installing the belt.
11. Re-position tensioner in two slots in bottom panel just in front of motor. On my model the bend in the spring will be on the right side with the idler pulley to the left, when viewed from the front.
12. Ensuring the belt isn't twisted, thread a small loop of it through the opening in the tensioner just below the pulley.
13. With the left hand, push against the tensioner spring while working the loop over the drive pulley.
14. While supporting drum with one hand, remove whatever you put under the drum to support it.
15. Replace front panel by aligning the slots with the tabs near the bottom and lowering it into place.
16. Carefully slip the drum opening over the flange on the front panel and replace hex screws.
17. Slowly roll the drum in one direction or the other until the belt aligns and centers itself.
18. Re-connect the plug for the dryer door switch.
19. Lower the dryer top and press until it snaps back into place.
20. Replace philips screws to secure lint trap and replace lint screen.
21. Plug dryer back into wall outlet, close door, set to dry, and press start.

My wife noticed a loud racket coming from the dryer. I took a look at it by opening the door and spinning the drum by hand and sure enough, the grinding, clunking noise continued. After a day of drying clothes, the noise got worse and then my wife said the clothes weren't getting dry at all. She could see the heating element glowing but the clothes would not dry. Sure enough, this was the case. While the dryer was turning, the outlet hose was still cold but the heater element was on. I went to the PartSelect site, entered the model number and looked at the common problems associated with noise. It said that the blower wheel was the second most likely issue. It also showed how to open the dryer and look for problem areas. First, unplug the dryer! Then, I took a putty knife (screwdriver would work - flathead) and pryed open the lid at each corner and opened the top. I then tilted the lid back against the wall to support the lid. There are two screws that hold the front panel of the dryer to the sides. They are on the inside of the cabinet up high near the top. I took these screws out and the front comes off by pulling the front panel away then up. There are three wires attached to a sensor on the front panel. I took a picture of these for reference and disconnected these wires to totally remove the panel. With the front panel off, I could see large clumps of lint trapped at the base of the filter screen. Now is a good time to vacuum this clean. Inside the cabinet at the bottom right, you can see the blower wheel. It was totally broken off the shaft that turned it. You can still spin the drum and see the shaft turn but the broken blower wheel would "clunk" around causing the noise. There are a small handfull of screws that hold the faceplate of the blower assembly on. Take these off and you will have full access to the blower wheel. DOn't worry about the wires on the sensor attached to the faceplate. If you want to take these off their clips, take a sharpie and write the color of wire each clip takes on the front of the faceplate for reference. The blower wheel is held on to the shaft by a circlip that is easily pushed off with a screwdriver or pliers and also a spring clip that is taken off with pliers by gripping the tabs with the pliers and squeezing the clip open. Save these two parts because the replacement wheel does not come with these pieces. I ordered the blower wheel, it was here in two days and replaced the wheel. Note: The wheel will take some effort to fully seat it on the shaft. You can take a hair dryer and warm the center of the wheel where the shaft will go thru to make the install easier. Do not use a hammer to beat the wheel onto the shaft or you will be ordering another wheel. I put my left hand behind the blower as support and pushed the wheel onto the shaft with my right hand and using a towel to cover the wheel center as padding. Reinstall the spring clip over the wheel shaft support and then pry the circlip back on the end of the shaft with pliers, reinstall the blower faceplate, reconnect any wires, reinstall the dryer front panel by first leaning the panel out and dropping the front panel onto the cabinet tabs at the bottom and then closing the front panel and screw it back down with the two screws. Reattach the three wires, close the lid, plug it in and your back in business. It took me longer to write this than it did to repair it. Good luck!

I watch the video and played it again while I was working.
I am a 54 year young woman and I did it.

I removed the lint trap then the dryer cover from top and front side. I placed the belt around the dryer drum being sure to put it on the correct side with the grid side against drum. I coiled the belt around the pulley and motor tract. Replaced everything in opposite order in which it was removed.
Video from website was very informative and helpful. I was able to follow along step-by-step to replace the dryer drum belt. I am officially a do-it-your-selfer!!!

I took the back of my dryer off to see if the problem was there. I saw that the belt was broken and laying on the inside of the dryer. Took belt and went on line (Google) my KitchenAid Dryer from it's model number. The website was PartSelect. Found the belt I needed and saw a video on how to replace the belt. I called to order the belt and spoke to Steve, which help me with all my needs. Steve knew just the belt I was looking for and placed my order. The belt arrived a few days later. While I was waiting for the belt to come in, I removed the front of the dryer and get ready for reinstall. It took me about 15 minutes to install the belt and put the front of the dryer back together. I found PartSelect to be very helpful and saved me, maybe $150.00 by not having to call a serviceman to do the easy replacement. Thank you Steve and PartSelect, now I'm number 1 with the wife again.