MUE15PDAYW Maytag Dryer - Instructions

followed instructions on youtube. The only hitch was threading drive belt back on. the video showed from back instead of front.After I was done I noticed an access door in back that would have helped.

I use U Tube watched Video, you have to take apart the dryer, but pretty simple to do. The drum rollers were very easy to install, make sure to have snap ring plyers, installing belt was easy too, make sure to put it back on it the way it came off, mine was ribbed side down on drum. Take a picture if necessary. Getting the belt on the pulley right is the most important part, the rest is just reassembling,

I made the mistake of repairing my old maytag neptune dryer with cheap eBay rollers and they crumbled apart and made a ton of noise within a month. I replaced them with quality OEM parts from partselect.com and my dryer is running like new. It's easy to do with common household tools and there are even easy to follow instructions available online.

As the dryer would be going you could hear a grinding noise every other sec or so, like sandpaper sanding metal.

Disassemble as per video on this site and install replacement felt seal.

Took a bit to tear down and change and reassemble but well worth the time as there is
no one in our area that does this type of repair(s) any longer

Changed motor

I followed the YouTube video for pulling the heating element to remove and place the thermostat. The actual thermostat removal and replacement was pretty simple. Most of my time was spent removing the front panel, pulling and reinstalling the heating element.

Moved the front door/panel two screws at the bottom of the panel.Then removed the front plate and support for the drum assy. four screws.Then loosen the belt and removed the drum assy. to get access to the drum roller to the back top right,.Used snap ring pliers to remove the clip cleaned the shaft an installed the new roller with the fiber washers and installed per instruction from your video,Also replaced the belt and put all items back in reverse order.It worked like a champ so easy,I would recommend your web site and videos to any one who wants to do it yourself. I have used you in the past and will continue using you for other items for parts and support.

i took off the door and the front of the drum and removed the drum. I removed the locking clip from idler pully and replaced and lubricated the shaft and slid the new idler pully on. I hung the belt over the back and put the drum back in and aligned the belt and turned by hand to get the belt in the correct position. Belt came off a couple of times because i think the belt was twisted. installed the front panel and the door, plugged the cord in and started it up and it was perfect.

Followed the video. Hardest part was getting the belt around the ideler pulley and motor pulley without seeing. But I got it! Thanks to this site you rock!

Removed front of dryer, removed inner cover, slid roller belt off of drum to remove drum. Only tricky part was the two clip rings. My pliers had .070 tips and the ring holes were smaller so I had to run to HD to buy a pair with various size tips, ended up using the .047 tips. Only one wheel was squeaking when I rotated them by hand, but I had ordered both as recommended here so I replaced them both. Put everything back together feeling the belt to make sure it was not twisted and rolled smoothly when I rotated the drum by hand. Works great now. Lots of thanks to this site and all the posters who share their info!

I watched a video on YouTube for the disassembly of the dryer. The parts replacement took less than 20 minutes; the rest of the time was spent on disassembly and reassembly.

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

repairmen said to buy a new dryer! or replace the motor! DO NOT EVEN THINK ABOUT IT!

It was the spring washer that was rubbing against the metal that was causing the very loud noise. The fiber washer that is used on the shaft on both sides of the roller had worn though and allowed the metal-metal contact. The fiber washer wore out! The fiber washers are very cheap!!!! in comparison to a motor or new dryer!


The drum rollers that support the rotating drum eventually wear out the fiber washer.
UNPLUG THE DRYER, DISCONNECT THE VENT
Remove the two screws on the lower front of the dryer panel, probably after you have tilted the unit backward. Remove the front panel by tilting out the bottom as there are two clips at the top. AFTER DOCUMENTING the CONNECTIONS - Disconnect the wires from the switch which is mounted on the front panel.
Carefully put the dryer on its back - be careful of the dryer vent to avoid damaging your floor or dryer vent!
Carefully pull the dryer drum up out of the dryer - as this is done the belt which moves the drum will fall away from the drum. I suggest before you remove the drum to eyeball the way the belt is tensioned and wrapped around the motor driveshaft, guard and tensioner. This will be the most difficult part of reassembling the machine. Some visual understand, maybe even pictures will help you later to get it installed correctly back into proper position... and it is NOT intuitive!
Once the drum is removed, the rollers are accessible. Rotate each and find the squeaker!
I recommend you replace the fiber washer on both, even though only one may be squeaking at this point (the other will be close to being worn out as well!).
I will not document the replacement of these parts as the assembly seems well documented elsewhere. I suggest you remain using the spring washer if there - as the after factory replacements do not seem to provide spring washers.
I would also suggest replacing the dryer drum belt, it is worn, after this many years, and putting in a new one will keep the dryer running for many more years. KNOWLEDGE IS POWER - USE IT

After taking apart the machine (applianceaid.com has slideshows for most major appliances - very comforting and reassuring - highly recommended), I used a shop-vac to clean up all lint and dirt. After getting the retainer ring off the drum roller shaft (snap ring pliers highly recommended), I replaced the drum roller along with the glides which were completely worn through (rivet gun required). I reassembled the dryer to find that the drum wouldn't turn, so I placed another order for the other drum roller and replaced the belt too. Back in business.

looked at video on your web site my wife and I decided to try it ourselves we are 70 and 71 And I am in a wheelchair just had surgery so we ordered parts. received parts looked at repair video a couple of times and went for it. during process we had some moments of frustration but we went back to video. end result, screech is gone. could not have done it with out video thanks.