DE408 Maytag Dryer - Instructions

Removed back panel of machine which exposed badly worn idler pulley. Have had problem before on another dryer so I was sure what problem was before I started. Removed snap washer and cloth washer and then bad pulley.(It was very worn and wobbly).Cleaned shaft with small piece of emery paper and put two drops of oil on shaft and replaced old pulley with new one.Put back washer and snap washer.Drive belt had slipped away from its proper position so I had to remove the front panel of the dryer to place the belt back and realign it on the drum and around the new pulley and the motor drive shaft. Not really that difficult.....Machine now runs like it's brand new.....

Unplugged the dryer, Very important, there is voltage on on of the wires to the heater.
I first removed the 2 screws on the lower part of the front cover and rotated this out of the way, no need to disconnect any wires. removed 2 small screws that hold the heater assy. cover plate and the one screw in the front bottom of the heater assy. I then removed the one screw at the top back of the heater. this completely frees the heater assy.
I then removed the push on wire from the thermistor and the other wire from the lug and I transferred the thermistor to the new unit. Now it is time to reverse the process making sure the entire circumference of the heater assy goes into the hole in the back. This can be a little tricky if the new assy is out of round. Just work it in, it will fit. Very easy, only about 20 min from start to finish...

The directions for the door latch kit told you to take the front of the washer apart to remove the old latch. But in my case the latch was broken in such a way that was not necessary. The new part just popped into place! No more fridge magnets holding the door closed!!!

And the new lint filter is great, the old one was so gunked up with old lint it was becoming difficult to clean.

I don't really know how old my dryer is, I purchased it used about 3 years ago.

Just pulled out the old filter and inserted the new one. went great and fit good.

No tools required, just insert the new lint filter in place of the old one. My dryer is about 20 years old. I think I was lucky to even be able to find a replacement lint filter.

Pried off old pads - used hammer to tap on new pads.

Locating replacement parts was the problem until I found partselect.com

I bought a new one and replaced it.

Removed the two lower screws holding front of dryer assembly in place and "unhinged" it and stood it up on floor. Then I unclipped the two wire leads on inside of dryer door assembly and moved assembly completely out of work area. Next I removed the four screws holding the tumbler frame in place and removed that frame from the work area. Now you can access the blower wheel "frame" and remove 5 or 6 hex screws to get that off and out of your way. You DO NOT have to remove the dryer drum and/or drum belt to complete this repair, so save yourself some work and leave it in place!! Once the blower wheel frame is off, use pliers and a flatheaded screwdriver to get the small outer retaining clip off, and then just pliers to get the wheel retaining ring off the wheel shaft. Put on the new blower wheel, use pliers to replace the aforementioned wheel retaining ring, and then the small outer retaining clip...VIOLA! You're finished! Dryer will run like new with a smooth purr instead of that dreaded rumbling sound.

Took longer to open the box that it did to drop the new lint filter into the dryer. Washed a load of clothes and the new dryer filter worked great

Thanks.

R. Bonker

after that every thing went very well

Unplug the dryer. Remove two screws to remove the front drum housing. Remove 4 screws to remove the front drum housing. The front panel and front drum housing do not need to be unwired to work on the blower. Loosen wire harnesses and move panel and housing out of the way. Remove 2 spring clips holding the blower assembly to the motor shaft. Remove blower. Install new blower and re-assemble in the reverse order. The other stories written on the subject were spot on. This repair also made the clothes dry more quickly. I did not realize that long before the ryer made noise, there was a reduction in air flow. A simple vacuum switch to monitor air flow would tell you when there is a problem or that the filter/duct needs to be cleaned.

By watching a video I disassembled the front and took the dryer tub out and replace the two rollers and it took about 60 minute.

Removed front cover.removed 4 screws holding drum in place. Cleaned out lint from everywhere. Placed new belt over drum looping it over idler arm & motor pulley. Pushed drum back ; rotated drum to see that belt was engaged. Put front drum bracket in place. Put front panel in place with 2 screws at the bottom. Tested motor & rotation of drum; then checked heat. All worked fine. Took 1 hr. but most time spent cleaning lint.

Opened your replacement part and found a broken fin on the blower wheel. no way I was going to return it and wait another week for another part. Perhaps you folks need to inspect what you send out. 1 blower wheel with a broken fin and 2 clamps. Replacement was easy and quickly accomplished. Having replaced drum rollers and the belt this dryer is almost new. Thanks

I went ahead and replaced all the thermostats, heater assembly and jump wire which was very easy after watching the installation videos. The new heater assembly was a little tough to get to fit in. but managed to get it to fit. Turned it on but to my surprise no heat. Someone earlier had told me that a friend had the same problem and it was a faulty circuit breaker but I didn't think that could of been the problem. I then checked it and sure enough that is what was the problem, it was only get power on one leg of the breaker. Put in a new circuit breaker and every thing works great. I don't mind putting in the new parts at least I have a piece of mind that that it's in good shape and have back up spare parts if needed.