GDE7400 Maytag Dryer - Instructions

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well

I had to remove the drum. 1. remove lower panel. 2.remove the vent duct. 3.Remove the door (be sure to mark the door switch electrical wire with tape NO, NC, COM). the switch is marked. 4 Slacken the drive belt by removing from its idler pulley. 5.Pull the drum forward & out, by lifting the top without removing it (may have to struggle a bit by bending the sides of the dryer outward). 6.Large 3/4" socket remove the squrrel cage fan counter clock-wise. 7.Unplug the wire harness to the motor and with a large flat bladded screw driver push the spring clamps down & out-ward to remove them.
I always take pictures with my digital camera before removing a part so when I reinstall the part if a question of position or what went were I have it documented in my camera to view.
I install the belt and use scotch tape to hold it in place before I reinstall the drum.
The best part was being able to access the interior of the dryer to clean the lint out.
I hope this helps!

1: Removed heater cowling by removing 3 screws holding it in place.
2: Opened two halfs of the cowling by removing 4 screws on the flange.
3: Removed 2 nuts holding element ends to the cowling.
4: Removed bad element making note of how the element was threaded through porcelin element bracket/holders.
5: Installed new element.
6: Reversed steps 1-3

Knowing most mfgs. put prints under the conturo panal we started there.
Diagonstics required a multi meter.
The part was removed and the internet serched.
My local parts center was more expensive and would have to order the part. I called Partselect
found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.

I observed that the top of the dryer was affixed by two screws at each front corner. With these removed the top of the dryer could be easily lifted and with the front support panel removed the drum, drive motor and idler pulley could be accessed. This allowed the installation of a new drum belt in a short period of time. Installing the belt from the front lower left hand side proved very difficult for me but with the top raised and coming in from the top it was accomplished in short order. Thank you, Wesley Harmon

Press in the new female latch part with thumbs. Took about two seconds!

I pulled the face of the dry off by removing the two screws on the lower face below the door. I pulled the drum out by removing the two bolts holding the drum mounts to the frame. I put the new belt around the drum and remounted it. The access hole on the lower right corner on the back of the appliance allowed me to turn the drum to align the belt (and turn it right side up) with the pulley. It took a moment to figure out how to re-thread the pulley but was able to do it after only a couple of tries. All in all it was quite easy!

It was very simple. I removed the fromt cover on the dryer. The heating element was easy to get to and after removing all the attached wires and 4 nuts. The new element was installed, reattached the wire correctly and put the screws back in place. It was extremely easy to complete.

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

I watched the video

Removed the front panel by removing two front screws. Removed screws from front panel holding tumbler drum. Cleaned interior with a vacuum cleaner. (dryer is at least 16 years old). Removed what was left of rivets on damaged glides with a drill, and cleaned area well. Attached new glides with rivet gun, and also applied glue to make glide and cork more secure. Replaced belts, and decided to reverse drum due to damage to drum from allowing glides to deteriorate to the point of putting scratches on the drum itself, allowing the new glides to rest on drum where there was no damage at all. This process was easy, and fast. We did make one error however, in not noticing that with our model, that there were TWO glides to be replaced. Luckily a local repair shop had one more glide so the job could be done the same day. The dryer sounds like it did when it was brand new. Very quiet! The comments from other home repairs helped very much in clairifying any possible errors. Fast delivery of parts, and the extra help was great. Thanks!

If I had waited until I reviewed the pack-up date that came with the part, the disassembly would have gone much faster. The part arrived in record time, several days before anticipated. Outstanding website, parts and repair experience!

Found step by step instructions on your website, they were posted by another do-it-yourselfer. The exact make of dryer that I have, and the drawings with part numbers listed was quite helpful. The bad motor came out easy enough and the new one was just like the old so it fit right into place. Strung a new belt around the tumbler drum and dryer is just like NEW. Thank you so much. Probably saved a couple hundred dollars.

How to repair a Maytag Dryer. (Call the nearest serviceman.)
Shut off the power and unplug the machine.
Open the 'box'. Two screws in the front near the floor and hinge open.
Make a diagram of ever screw and piece you remove.
Diagnose the problem.
Order the necessary parts from ....
Replace the part. (The element replace the second time in 30 years.)
Give the box a cleaning inside and out.
Put it back together.
Make sure all the parts you took out go back in.
Plug it in and turn on the power.
Test it.

Using a magnet to hold all the screws was helpful.
Having all the right tools is helpful. The requirements were pretty basic.
A good mechanical aptitude is essential or very helpful.
It is very important the exhaust port is patent. A leaf blower would be helpful in testing. I reversed the hose on our vacumn cleaner and packed foam around the tubbing to test it. (The local dealer warn me about using too much of the clothes softner.)
Karl Spees on behalf of my wife Soonja