MGD6300TQ0 Maytag Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Neil from Harwich, MA
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Flame when out to fast. Dryer did not get hot enough.
Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EUGENE from NEW HYDE PARK, NY
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door catch locking clip feel off while dryer is running.
Following the instruction video, using screw driver to remove the old one and push in the new one by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Comblarry from McComb, OH
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
broken catch
popped old catch out put new catch in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Hanover, PA
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door catch
As showed in the video, it was simple. Popped out the broken catch and popped in the new catch, less than a minute. Thanks for the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tntsplace.com from MCALLEN, TX
- Parts Used:
- W10239307
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The rubber seal on the Cabrio dryer door came off.
Clean the old seal area. I let it dry for a couple hours, just to be safe. Rubber gloves, I applied the adhesive to the door all away around the seal molding space. Then inserted the rubber seal. Going around with my finger pushing the seal tightly into place. Let dry over night and the next day I closed the dry and let it finish drying. Then came the washing day and the dryer worked like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Midge Tucker from Greeley, CO
- Parts Used:
- WP8572270
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
handle broke off the lint screen
Pulled out old lint screen. Pushed in new lint screen. Time 30 seconds! Why can't all repairs be this easy? ! LOL !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Danny from Godfrey, IL
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
latch was broken
Pried edge of latch with dull butter knife. Latch popped out. New one popped back in place. Took 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Ralls, TX
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door catch
Used putty knife to pry broken door catch off .... Snapped in new one. Took maybe two minutes !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hilda from Wilmington, NC
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door catch broke in two parts.
I used a screw drivers and put the old one out, and put the new one in. It was very easy for me to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Missouri City, TX
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken door latch
replacement - pry out the old, snap-in the new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LAURA from TWINSBURG, OH
- Parts Used:
- WPW10111905
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Door catch was broken
Well the Youtube video was helpful. BUT that only worked on a catch that WASN't broke. I had to bend it up and push it into the door. New one went in easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from LeClaire, IA
- Parts Used:
- WPW10111905
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
spring broke on door catch, door would not latch
As in the video: inserted putty knife behind catch lip above and below the catch. Video shows only doing on top or bottom, but need to do both and then pry out while pushing towards the center of the catch up and down. Not as easy coming out as in the video. Putting new catch in was easy...just slide into hole.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kellie from Norton, MA
- Parts Used:
- WP694089
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
blower wheel cracked and broke
i took the back apart to find the problem, then i went online to findout how tomremove the blower wheel, just googled it. Easy!Took itnall apart, just had a bit of trouble getting the wheel off, was on there very very tight. Ordered it through you, easy, and very very quick, received it in a day. I got an email explaining the reassembly process. Easy. Just follow it to a t and you will be fine. As a woman, this was an easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from FORT WORTH, TX
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Door Catch Very Worn. Plastic Keeper That Holds Clip In Line Has Broken Off The Back Of Catch.
Took my channle locks and pulled old catch out and snapped in new catch. Works great now. Cost me four dollars and 3 minutes of my time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from McKinney, TX
- Parts Used:
- WPW10111905
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
door catch broken
replaced door catch with part ordered from this website VERY EASY!! Thanks!!
Was this instruction helpful to you?
Thank you for voting!