MDE16MNAYW Maytag Dryer - Instructions

I followed the Part Select tutorial on Instant Repairman and retrieved the missing screws at the base of the dryer as described in the tutorial and after trying to reassemble the original baffle notice the baffle screw holes were stripped. I decided to fill the holes with a strong glue before reinserting the screw to temporarily keep the machine running until the new baffle arrived as it was just ordered the night before. When the new baffle arrived I decided to hold onto it as a spare if or when the original baffle broke off again.

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

Unplug the dryer and pull it away from the wall so front and back can be accessed. Remove front panel. Remove front drum support. Remove rear access panel. Disengage drive belt from idler wheel. Make careful note of course of belt and which side is "outward". Remove drum through front. Remove Rollers using circlip pliers. Remove nuts behind shafts. Remove shafts. Clean-up area and parts before re-install.

Install new Shafts and nuts. Grease shafts. Install new Rollers, washers and clips. Drape drive belt over drum while reinstalling from front. Remount drive belt over drive and idler pullies from the rear access. During this step it helps to have a helper to position the belt around the drum in correct fore/aft position, lying flat and without twists, smooth side against drum. Install front drom support. Rotate drum to seat belt before closing up. Install rear panel cover. Install Front panel. Plug it in and turn it on for a test.

Followed instruction video

my son did the installation according to your excellent video instructions

take screws out of front of dryer, pull front off to expose drum and replace baffle

Really easy to replace. All I had to do was remove the screws on the hinges and two on the other side. Used a nut driver to remove the brackets that hold the lid down. Secured the lid open and used the nut driver to remove the screws that hold the baffel son (two on each) and replace the baffel and secure with the screws. Reversed the the process and was drying clothes my first load of clothes in around 30 to 40 minutes. Process is really easy and I was able to do it by myself

I removed the front of the dryer and the drum support plate. I drilled out the old rivets and installed the Glides with the enclose rivets. The Glides came loose in a few days! The holes in the glides are larger than in the old Glides. I disassembled the dryer again and reassembled with my rivets. This time I held the rivet gun inside the perimeter of the dryer so that the head of the rivet is opposite the initial installation. So far, so good, except the dryer still squeaks. The idler pulley is now the culprit. White grease burned up. I reassembled with high temperature grease. If that does not work, I will need another idler pulley. The journal looks very worn. the dryer is 30+ years old.

Replaced the motor with a new one from partselect per the YouTube video. Had a problem with delivery of the motor. I paid for next day delivery. FedEx picked it up and it made it to the first stop, Indianapolis ok and then stopped. After a week went by I ordered a second one. That one came as promised + 1 day so I’m satisfied. The telephone people were very well spoken and attentive to my discomfort and again I’m satisfied. The motor was at least 25% cheaper than if I bought it from Maytag so the savings is significant, about $50.

I watched Steve the repairman on u tube then opened up the front of the dryer and noticed the part in my dryer was a little different than the one on the video. So I called in and I was reassured it was what I wanted. When I got the replacement part and before I removed the old part I took pictures of the wiring noticing the wires where changed from left to right I had to make up one of the 12 gauge wires and connectors with parts from the hardware store and the new part was shorter than the old part, but the machine all ready had screw holes where I needed them. I looked at my photos and wired the new part the same way I took the wires off the old part and put it back together and it works like new! saved money! the local guy is $150 to show up and start the clock. I also fixed the blower,EASY!

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

Remove the door and the plastic brackets on the other side of the door opening. Remove the front cover by gentally pulling from the top first. Support the dryer basket (I used an old towel and a block of wood. With a 1/2 inch wrench remove the Roller Shaft with the Drum Support still attached. Replace new shaft and drum support. (always replace both at the same time or you will find that the problem will come back much sooner.) Careful when installing. Make sure that the new non metalic washers (suppied) are propery seated when you are tightening down the nut.

After watching the great install video, I followed his lead and within 20 min had my dryer door fixed. This dryer was bought in 1986 and I really thought I was looking at buying a new dryer. How wonderful that I could fix it for less than $11. Easy to find web site, easy to find part, great instructions and fast delivery!

discovered it was a broken latch. Ordered the latch, only took 2 days to arrive and all I had to do was remove the broken latch and snap in the new one. I saved myself a service call. I'm very happy!!!!!!

I took out the old worn out part and replaced with the one I order.