LDE4000ACL Maytag Dryer - Instructions

If I had waited until I reviewed the pack-up date that came with the part, the disassembly would have gone much faster. The part arrived in record time, several days before anticipated. Outstanding website, parts and repair experience!

Firts replaced a thermostate - did not fix the proble. ( had a glow from the starter but no flame.)

checked igniter sensor OK (got no resistance) so replaced the two coils that sit on top of the gas burner. With new coils noticed a much brighter glow from the igniter and the gas line opened up to produce a flame

Dryer has workd successfully for the last 5 loads.

Able to run dryer with the front removed by holding in the microswitch activated when door is closed.

Turned off breaker, then unplugged it anyway. I need some room to attack this old dog! Pulled out of its hole beside the washer and went to work. Opps, don't forget the flexible vent, I broke it off about a foot from the dryer. Four screws on back, lower right to remove acccess panel. Next two screws under front panel, pull bottom out about a foot and it unclips at top. Read the 5 repair stories about replacing the motor as I took everything apart, all were helpful. Had to put motor in a vise to loosen set screw on pulley, lucky I had a 3/16 allen socket, that was the only hard part, unless you count getting screws out from under the freezer where I kicked them. Be careful. Still ended up with belt in v-groove on back part of drum (where it does NOT go) so had to reach in from front and pull it out about 4 or 5 inches. Things a quiet now and I am a hero around here. Thanks for the good help fellows.

I did it the hard way from the back by removing the motor. The easy way is from the front. From the front there are 2 screws about 5 inches above the floor. Also, remove the 4 screws in the tumbler behind the lent filter. Swing out the front panel from the bottom and it will release at the top. Remove 2 screws on left and right side of the front tumbler cover. It will come out now and you can get to the blower wheel which in my case was just spinning on the motor shaft.

No manual on this so had to remove about 12 screws to figger out disassembly,after locating the right ones[front]the job was easy.Remove front plate,remove drum bearing,remove blower front cover,remove snap ring,remove broken fan,clean fan shaft,slide new fan onto shaft[there is a flat in the bore of new fan]instal fan retainer on stub of fan,reinstal snap ring,reinstal the rest of the parts,test drive system[all sat]The part was exactly as ordered,thanks,Jim Thompson

Took out the old lint filter and put in the new one. Works great

Inserted new lint filter...one second! No tools needed. Price excellent!

First, I unplugged the dyer and then I removed all of the screws for the panel that covers the rear of the dryer. This exposed the cycling thermostat's location. I then removed the wires, one at a time so I would be able to put them back on in the same place. Then I removed the one screw using a nut driver and then put the new cycling thermostat in place. It was pretty easy.

I followed the videos on your website, but had to clean 30 years of dust and lint out in the process. Cleaning took the longest time.

After replacing the cycling thermostat failed to fix the problem, I jumped the Dampness sensor, overtemp sensor and flame sensor - no change, flame went out after 15 to 30 seconds. Ordered the replacement coils for the gas control and reconnected all sensors: solved!

Removed the frong cover and and internal sheild, removed and replaced thermostatic, wiring as original.
I had searched several other sites first for thee part, but none of them seemed accurate. Your photo matched the old exactly, giving me the confidence I wanted before ordering.

I opened the back acess panel and started the dryer. Looking at the motor and idler pulleys it was obvious by the frequency of the squealing noise that it was coming from the idler pulley.
I pulled the retainer clip and tension spring from the idler pulley and removed it. I applied some grease to the shaft and reinstalled the idler pulley.
The squeal was gone confirming that the pulley bushing was dry. I ordered the new idler pulley and when it arrived the next day I cleaned the grease off of the shaft and installed the new idler pulley. Problem solved.

1. Removed two screws from front panel.
2. Removed panel.
3. Removed four bolts off tumbler face.
4. Removed face.
5. Removed drum and belt.
6. Vacuumed.
7. Replaced idler spring assembly.
8. Replaced drum.
9. Replaced belt.
10. Rotated drum to make sure belt was properly seated.
11. Replaced tumbler face.
12. Replaced front panel.

The repair was very simple.I removed the door and the front cover.Right in front of the blower housing sat the temperature control thermistor.All that was needed to do the swap was a nut driver.Everything I read said the high limit thermostat may of been bad but it was fine.Ordering the parts was easy and fast all I needed was the model number and all the charts and numbers were easy to find.Thank you Parts select..

Insure the double pole breaker in the breaker box is functioning properly.