MDE7400AYQ Maytag Dryer - Instructions

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

Watch the video. Very, very easy

Did an internet search for parts for my older Maytag dryer. Landed on PartSelect and man I am glad I did! Entered my model number and boom! Complete schematics on the dryer, with part numbers. Also have diagnostic questions to point you in the right direction. Figured out what parts I needed, ordered via phone. Fantastic customer service. PartSelect also has excellent installation videos you can watch to assist. Took me a little over an hour to open up the dryer, replace the drum rollers, drum belt, idler roller and both front and rear felt seals. Buttoned dryer back up, hit the run switch and it purs like brand new. I cannot recommend PartSelect to highly. Great company, great customer service, quick shipping.

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Replaceing the timer was very easy. I removed thgree screws from the top panel of the dryer. Unpluged the wires connected to the timer and removed it from the panel. Simply reversed the process to install the new timer. The whole process trook less than five minutes. To think I spent a year fighting with the dryer when the repar only took a few minutes...

Took off the front, took thd drum off, removed old belt, placed on new belt ptu everything back together.

I removed the defective assembly and snapped in the new one. It was very easy! Hopefully this one will last longer than a year. This is the 3rd sensor assy for this 3 yr old dryer in 3 yrs.

I removed the 2 screws that hold the door and removed the door. I then removed all the screws that hold the front panel and removed the front panel. Then I was able to lift (on hinges) the top panel. I then removed the screws that hold the front drum housing, then removed the drum and belt. At that point you have plenty of room to access the idler pulley. I removed the Idler pulley spring. Then I removed the the screw holding the Idler arm and shaft. Reinstalled in reverse order.

Save the money and buy the part with partselect. My dryer problem was obvious. Before I purchased the part I jumped on YOUtube to see if there was a repair video that matched my problem. FRIELINK5 had a very thorough video. This guy did it with one hand and overall it looked easy. Then I ordered the part. When it arrived I gathered all of the tools first. Rewatched the youtube video, then installed the part. I recommend going through parts select problem determination if you do not know what is wrong. Follow the instructions and purchase the part. I saved probably over $125. House call 50$ + Labor and part $100 from a service call. TRY IT save money.

The YouTube video on how to replace the baffels was excellent. After watching the video, it was a piece of cake.

Removed door and front and drum. Removed fan assembly. Be careful when working fan off of motor shaft. Unhooked wiring from motor. Removed clips. Replaced motor. Reverse procedure to put dryer back together. Now works like new. Very, very, happy. Part came in 2 days using standard shipping. Way better than buying a new dryer.