LDE7500ADW Maytag Dryer - Instructions

After replacing the cycling thermostat failed to fix the problem, I jumped the Dampness sensor, overtemp sensor and flame sensor - no change, flame went out after 15 to 30 seconds. Ordered the replacement coils for the gas control and reconnected all sensors: solved!

Inserted new lint filter...one second! No tools needed. Price excellent!

Took out the old lint filter and put in the new one. Works great

Took it apart according to the videos, replaced about all moving parts (almost). Put it back together and still made noise. It turned out to be the blower wheel. Ordered a new blower wheel and installed it. Works great and has mostly all new parts. The website was great!!

I followed the videos on your website, but had to clean 30 years of dust and lint out in the process. Cleaning took the longest time.

The repair was very simple.I removed the door and the front cover.Right in front of the blower housing sat the temperature control thermistor.All that was needed to do the swap was a nut driver.Everything I read said the high limit thermostat may of been bad but it was fine.Ordering the parts was easy and fast all I needed was the model number and all the charts and numbers were easy to find.Thank you Parts select..

Removed the frong cover and and internal sheild, removed and replaced thermostatic, wiring as original.
I had searched several other sites first for thee part, but none of them seemed accurate. Your photo matched the old exactly, giving me the confidence I wanted before ordering.

I opened the back acess panel and started the dryer. Looking at the motor and idler pulleys it was obvious by the frequency of the squealing noise that it was coming from the idler pulley.
I pulled the retainer clip and tension spring from the idler pulley and removed it. I applied some grease to the shaft and reinstalled the idler pulley.
The squeal was gone confirming that the pulley bushing was dry. I ordered the new idler pulley and when it arrived the next day I cleaned the grease off of the shaft and installed the new idler pulley. Problem solved.

1. Removed two screws from front panel.
2. Removed panel.
3. Removed four bolts off tumbler face.
4. Removed face.
5. Removed drum and belt.
6. Vacuumed.
7. Replaced idler spring assembly.
8. Replaced drum.
9. Replaced belt.
10. Rotated drum to make sure belt was properly seated.
11. Replaced tumbler face.
12. Replaced front panel.

used a utility knife to open the box in which the part was shipped, discarded the old filter and inserted the new one

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

first i removed the screws holding back cover. Then I remeved nut from tumbler roller shaft. Then I slid shaft from roller .I removed roller then replaced with new one. Installed new shaft then replaced back cover. recieved parts from parts direct very promptly & they were the right parts the first time thanks very much

From the noise level and info on this site, I assumed I needed to replace the drum rollers. I ordered two, along with the Roller Shaft, and a replacement belt (I assumed that would eventually need to be replaced so why not now).
No need for me to repeat the excellent reviews/instructions already on this site. Basically, it was an easy job that took about 2 hours, mostly because I took the time to clean every nook and cranny I could find.
Once I assembled it back up, the shriek was gone but the rumble noise was still there. I now realize that the blower wheel must have a worn out d-hole that mates with the motor shaft. So, I will have to order that part, get it installed and I am confident that I will have a "new" machine once that is in place.

Disassembled per instructions. Additional time used to clean inside unit.. Its much easier to install belt on motor pulley and tension pulley ( Roller) from rear access panel. Also ensures proper belt alignment on all items.