MDE6700AZW Maytag Dryer - Instructions

remove top of dryer,remove dryer door, then remove front of dryer themostat is in front on exhaust duct has one white and one yellow wire two screws hold it in . Door switch is a push in connection with a three wire connector.

Remove lower bottom cover (two screws on bottom) with screw driver. Remove old radiant flame sensor from left side of tube with ignior by using socket wretch. Remove wires with needle nose pliers. Put new part in: put wires back on, insert part's lower tab into the tube ( there is a small slot) use socket wrench to tighten screw at top. Put bottom front panel back on and screw back in.

After reading other posts, I learned that "tO" meant that the thermistor was open. Also, I read that this part would bench test with a multimeter correctly but could still malfunction in the dryer. FIRST UNPLUG DRYER. After checking all of the exhaust ducting including inside the dryer for any blockages that could result in an overheating problem I decided to order a new thermistor. To replace thermistor: First, there are two screws at the rear top that you remove and the top tilts up and comes off. There are four screws on the top front that removes the front control panel. Next remove the screws at the top of the dryer, two screws in recesses behind the door and tilt front forward while unplugging the door switch. Lift and remove front with door attached. Remove screws from exhaust duct and slide down and out. Thoroughly clean inside of duct and fan blades. Clean out any other lint build up. Locate thermistor to the right of duct, unplug and remove two screws. Replace with new part and reassemble while not forgetting to plug the door switch back in. At the rear of dryer, remove screws around exhaust duct and remove. Dryer will have to be slid away from wall about three feet to remove duct from inside dryer. Clean thoroughly and check/clean and check for blockages in ducting from dryer to outdoors. Re assemble making sure rear duct engages the front ducting properly.Plug dryer back in and enjoy.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

Test thermal fuse for resistance. If has 0 resistance you have a bad fuse. Also check voltage going to wall outlet. Must use at least 600 volt tester. Motor will run on 110 volts, but will not activate heating element. Heating element must have 240 volts to operate. Always make sure you turn off power when working on electrical problems. Be safe and good luck.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

Remove 2 screws which hold dryer/washer together on back. Remove 2 screws back top dryer and slide top back. Remove 4 screws top dryer that hold timer panel. Remove 6 screws that hold front panel on..4 on top of panel and 2 inside door. Disconnect wires to door at slide connection. Unplug dryer..this is actually 1st step. Remove 1 screw on heating element (lower right). I found that by removing the red wire the element will wiggle loose and come far enough out to disconnect black wire. There are 4 other terminal connections which are jumpers that will slide out with element. Note where wires attach and remove all. Use Multi meter on highest ohms setting or a continuity tester to test heating element - thermostats - thermal fuse. They should all have continuity between terminals. Replace any that don't . My thermal fuse was open (no continuity). I replaced it and had heat..but inadequate heat. Got new thermostat which fixed problem. Video I watched said to replace them together..I guess he was right. I suggest that while you have dryer pulled out to take time to check/clean dryer vent..also flapper outside.(mine had lint built up in hinge and prevented flapper from closing letting cold air and anything else in). Parts Select has great videos/skematics and even with "snail mail" delivery part was there in 2 days. They are the best!!

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

I had a problem a couple of months ago with the dryer not heating and replaced the thermal fuse after checking the the parts with a voltage meter and the dryer worked fine. When I did the repair I also cleaned all the lint out of the dryer, exhaust, and the vent. It worked fine. A couple of weeks ago my wife commented about how hot the dryer was and it seemed unusual. I realized there was another problem but before I could check it, the dryer stopped heating again. Some time ago, the sensor dry funciton quit working so I just went ahead and changed all the electronic componets, the two on the exhaust tube and the two on the heating tube. I assumed the high limit thermostat failed. After unplugging the dryer, I took the two screws loose on the top backside of the dryer that hold the top in place and removed the top, sliding it back. I removed the four screws holding the control panel in place and rotated the panel forward, then up and out of the way. I removed the four screws along the top of the front panel, then the ones from around the opening on the front, and the front door. There was one screw that held the heating tube. I removed it and the tube slid forward. I took the front wire lose and rotated the tube clockwise to pull it out and took off the back wire and changed out the thermal fuse and thermostat. The exhaust tube was right there in the front and all I had to do was change out the parts on it. Everything went back to gether as easy as it came apart and when I plugged the dryer back in, it worked just like new.

Replace the igniter and dryer did light and after 3 minute went out. so I ordered to gas valve selenoid's and replaced those and everything it working properly

Unplugged electrical cord to dryer. removed the front cover 2 screws on the bottom. Lifted front cover off. Unplugged the 2 wires going to the old flame sensor. Used nut driver to remove 1 screw holding the flame sensor in. Removed old sensor replaced with new one. Reattached the 2 wires back on to the new flame sensor. Tested. Flame stayed on longer! Dryer works great dryer is 20 years old and still running like new now. Part was the exact match I needed.

This was a simple repair. Removed the small access panel where the vent pipe comes through, the roller is right there. Unscrewed the support roller bolt, looking for all the pieces that had broken and fallen inside the housing of the dryer. Using the washers and nut from the old one, put the new roller in place, be aware that you have to lift the drum a little bit to get this new roller in. It could take two people depending on your strength. Tightened down the roller, spin the drum by hand to make sure it was ok, then put the access panel back on and fired it up for a test run.

after removing 2 screws securing top of dry i isolated the humming noise to the electronic board. Dryer would not turn on but drum light would work. 2 screws hold the electronic mount, and 1 screw hold electronic board. all electrical connection on board easily unplugged. connected new board installed in mount with 1 screw and then installed mount with two. plugged in and pressed power switch and electronic timer came up and dry started at the press of cycle start knob. the key to this repair was the stuck relay humming sound being generated by the either the relay or transformer on electronics control board.

The repair was pretty easy to install the heat element, but had to replace several other parts do to the manufacturer that had broke off

unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.