11066134610 Kenmore Dryer - Instructions

Took the two screws holding the lint trap to top. Used a putty knife to loose the clips holding the top of the dryer up so it could be hindged up for access. Used a nut driver to remove the four screws hold the front door on. Removed the lower dust panel, just clips holding in on. Pull the dryer drum out along with the broken belt and old belt tensioner. Took shop vac and cleaned lint and removed about $2.00 of loose change from the base. Installed the new drum supper wheels. Held belt around drum to put back in. Looped the belt through tensioner and around motor drive pulley as shown in instructions. Put front door on only to find the felt around the door had slipped making the drum hard to turn. Pulled the door back off and laid the dryer on it's back before putting the door back on , so you can run your hand around the door to make sure the felt go inside the drum. Put the four screws back in the door panel before uprighting the dryer. Sucess the drum turned freely. Put other remaining panel and srews in lint trap . Hook the dryer back up to vent, power and gas, and turned on the dryer. Runs like new!

The brightness of the light was because the door switch was allowing too much current to the light bulb when the door was open but the switch would not swich the current to the dryer motor when the door was closed. After a day or so of this bright light it burned out. I removed the two screws on top that hold the lint trap in place then I could access the switch by sliding the top of the dryer forward and lifting the it as you would lift the hood of a car. The switch is on the right side and plugs into a three wire connector and only fits in one way. Cheap and easy fix after unplugging the dryer from the wall power outlet.

Determined that the door switch was not making contact. Removed the lint screen, removed two screws in the lint screen housing, pulled the top of the dryer up at the front of the dryer. This provided access to the door switch which was mounted on top.

This was super simple - even I could do it! I followed the 3-step instructions which basically described how to hold the new handle and pushed it into the holes in the door. Less than 30 seconds and no tools.

I use the manentance kit that was not the problem. I end buying the drive motor and that was it. I was happy with the service I got from part select, overnight mail what more could I ask for? I am also glad I replace everthing with mainentance kit. Thank you for your help john degnan

After getting the part and sizing up what to do. I removed the 6 1/4 hex nuts from the back. I removed the 2 hinge nuts 3/8 and popped the lid of the dryer up. It wasn't coming up all the way. I removed the lint filter and removed the two #1 Phillips screws that held the lid to the duct and it came up easy.The switch itself was clipped together and came apart with ease. 2 #1 Phillips screws held the switch in place and quickly tightened down the new switch. I clipped the new switch to the old lead and just reversed the order putting it back together. The light worked and the drum stopped when the door was opened during the cycle. The part matched perfectly and there was no guess work about clearance. It was an easy repair.

I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.

I had never tackled a job of this kind. It took me a little longer than it should because I was being very careful. Next time it will be easier and faster. The instructions that came with the parts was fantastic. I will be ordering from this site any time I have an appliance to repair. In the past I would have bought a new one. Saved a bunch of Bucks and works like new.

Pretty much followed your great video: . Watching it gave me the confidence that I could accomplish the job myself.

I followed the accurate video. I'm sure I saved a lot of money over having a repair man come out. Now maybe my wife will believe that I am capable of repairing some things myself... eh, probably not.

Did as your video instruction. To me the order of work needs attention: Remove the switch, unscrew 1st, then remove the hook and wire connection. Installation: connect the wire first, then hook to the frame, the last step is screw in the switch. That should prevent accident dropping the switch inside the dryer.

Unplug power supply or switch off breaker that supplies electricity to appliance .. Remove lint screen there's two star head screws that holds lint screen holder to top cover remove them, using a flat head screw driver there are two clips between top cover and body push screw driver to depress clip while lifting corner do in other after top cover will become free from clips raise top. Unplug old switch remove two star screws to free switch from inside dryer door

Once I had determined that the door switch was broken (the black actuating arm was broken) I ordered a replacement. The procedure to replace it is the reverse of removal of the broken part: unplug the appliance to begin. There are 2 screws that hold the filter frame to the top of the dryer; these are removed and set aside for reuse. The top of the dryer can now be pulled up to gain access to the door switch. Make sure you leave enough space behind the dryer to prop the top up without letting it go backwards. Disconnect the wiring harness plug for the door switch and the unscrew the switch. There are 2 screws accessed from the upper right corner of the open door. Replace the switch, guiding the 2 screws into the mounting holes of the part, remembering to not over torque the screws, connect the wiring harness, close the lid, replace the 2 filter housing screws, plug the dryer back in to the electrical outlet and you should be good to go.

I followed your online video of how to install the new part . I did have an issue getting the top cover off the machine - the video said to pop off at tabs but no such existed- I had to remove 4 screws on the back of the dryer & lift top off - no big deal Then I had some trouble getting the old part unplugged - required two pliers either side to pull apart- VERY securely fastened. Otherwise just so so simple. FIXIT housewife!

After reading on line that the door switch fixed the described problem 48% of the time I decided to order a door switch first. Very easy to follow the video instructions that were on line. In less than 15 minutes my dryer was working again.