11066134610 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ray from Boulder Creek, CA
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Drum would not turn. Broken Belt
Removed top cover. Removed front cover. Removed Drum. Located the broken belt. Found that there was no tensioner in the unit. Replaced drum rollers. Put in new tensioner. Repaced Drum with belt around it. Installed belt through tensioner and onto drive pully of motor. Supported Drum with wood block. Turned on dryer to insure drum turned without any problems. Removed wood block. Replaced front cover and top cover. Repair compete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Rocky Mount, VA
- Parts Used:
- 4392065
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Loud rumble and finally the drum stopped because the belt broke
I opened the top and front of the dryer. 1st I pulled out the drum and cleaned up the lint and mess from the busted support roller. Next it was a matter of looking at the enclosed drawing and instructions. I could not believe it was that easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from auburn, IN
- Parts Used:
- 4392065
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set, Wrench (Adjustable)
drum made a thumping sound was really noisey
pulled dryer away from wall took screws out of lint screen lift top removed 2 screws one on each side of front at top and removed front panel. pulled belt off drum removed drum rollers tension pulley and while i was at it pulled back cover off of heating element and blower blew everything out with air hose did a total cleaning installed everything in reverse. i was amazed how fast the parts came the dryer was only down 2 days and it runs like new even if it is 20 years old i highly recommend parts slect and i will use them in the future
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from S LAKE TAHOE, CA
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Bad Motor, Would not start.
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from PFLUGERVILLE, TX
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
The original motor stopped working
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from MIDDLEBORO, MA
- Parts Used:
- W10861225
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broke handle on dryer and replaced it with a new one
Followed the directions and just snapped the new handle in place
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from NORTH ADAMS, MA
- Parts Used:
- W11429587, WPW10529197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door catch on dryer door
Gently remove the door bezel by prying it off with a small screwdriver. Then remove the door catch from the door with the same screwdriver. Be careful not to drop it in the door. I did and had to fish it out with a small hooked pick. Install the new door catch by sliding the top in first then the bottom. Again, careful not to drop it in the door. Then snap the door bezel back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annette from CADILLAC, MI
- Parts Used:
- WP3406107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stop when I opened door and light would not come on
Just like your video said. Very easy. I will purchase from you again. Thank you!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cris from GLENDALE, CA
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the metal plate connecting the door catch was broken, so I ordered the part
I pushed one end of the catch on upper side the hole and when locked, I pushed the other end of the catch to the lower side to get locked. To complete, the white cover was inserted on top of the catch and done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie from BEND, OR
- Parts Used:
- 49621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling feet on dryer.
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from tewksbury, MA
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch had crackedt
took out old ,twisted in the new one it was nice to have the right part the first time!! thank-you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BLASDELL, NY
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch broke
Remove the protective cover on door with screwdriver, pop out the old catch, snap new catch in place, replace protective cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from SHELBYVILLE, KY
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not stay closed.
Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WINCHESTER, VA
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dryer door would not latch. The door latch was broken and needed to be replaced.
Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from GRESHAM, OR
- Parts Used:
- W10861225
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Handle on dryer door broke.
The part arrived in the mail. I used a pair of kitchen scissors to open the package. I removed the part from the plastic bag, and snapped it into place on the front of the dryer. Total time: 15 seconds.
I wish all my repairs were this easy.
I wish all my repairs were this easy.
Was this instruction helpful to you?
Thank you for voting!