110C62102310 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Yvette Joan from DUSON, LA
- Parts Used:
- WPW10185982
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
No problem
My son did the repair and said it was so easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Helen from WEST MONROE, LA
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
belt broke
watched your video on 'how to' and did it like man showed..no problem
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- albert from ROEBLING, NJ
- Parts Used:
- 341241
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
dryer will not rotate
the video was very well done and able to understand. disconnect power ,remove lint trap,remove 2 phillps head screws, push putty knife in front seam line about 1'' in from corners to release top assembly ,lift up and support, disconnect wire connector ,remove 1 screw in each front corner lift front panel off while holding drum, remove broken belt,install new belt with grooves against drum ,feed around tensioner pulley and onto motor shaft pulley ,spin drum by hand to make sure belt tracking etc. reassembly in reverse.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from POLAND, ME
- Parts Used:
- W11778253
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Lint filter cracked
Removed old filter, replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie from BEND, OR
- Parts Used:
- 49621
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
No leveling feet on dryer.
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use the adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from SHELBYVILLE, KY
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Door would not stay closed.
Replaced door catch on dryer door. Followed video on Whirlpool website and it took less than 10 minutes. The dryer works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from WINCHESTER, VA
- Parts Used:
- W11429587
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Dryer door would not latch. The door latch was broken and needed to be replaced.
Once I received the new latch I removed the latch cover with the flat head screw driver and worked out the old latch. I then positioned the new latch and snapped in place. I then replaced the cover and shut the Dryer door. The door latched and the repair was complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RICHARD from LEVERING, MI
- Parts Used:
- WP3406107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not turn on.
I just followed the instructions from this site for the door switch part and had it running in 10 minuets. This site made it very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Annette from CADILLAC, MI
- Parts Used:
- WP3406107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not stop when I opened door and light would not come on
Just like your video said. Very easy. I will purchase from you again. Thank you!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from SANTA MONICA, CA
- Parts Used:
- WP3406107
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer wouldn't turn on.
Noticed the door switch was loose and the light bulb inside dryer didn't stay on. Researched the problem on PartSelect. Followed the directions given: Take 2 screws out of top of lint trap. Pry top off of dryer with putty knife. Unscrew 2 screws in dryer door frame holding in old switch. Uplug and remove old switch. Plug in new switch and put screws back in. Close top of dryer. Reinsert 2 screws in lint trap. My 20 yearn old dryer works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from NORTH ADAMS, MA
- Parts Used:
- W11429587, WPW10529197
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken door catch on dryer door
Gently remove the door bezel by prying it off with a small screwdriver. Then remove the door catch from the door with the same screwdriver. Be careful not to drop it in the door. I did and had to fish it out with a small hooked pick. Install the new door catch by sliding the top in first then the bottom. Again, careful not to drop it in the door. Then snap the door bezel back in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from tewksbury, MA
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch had crackedt
took out old ,twisted in the new one it was nice to have the right part the first time!! thank-you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean M from CHESAPEAKE, VA
- Parts Used:
- W11778253
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint would no go throw
Received the new lint removal from the box and install it easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from HUNTSVILLE, TX
- Parts Used:
- WP3406107
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light wouldn’t work and dryer wouldn’t stop when you open the door.
Remove the lint screen, then remove the two (2) Phillips screws that are at the entrance of the lint screen compartment. Take a putty knife and insert it under the top pannel of the dryer about 1” in from the outside and push the putty knife in as you lift that corner of the pannel. Repeat on the other side. Then raise the lid and prop it up. The door switch is on the right side just behind the door on the inside. Open the door and remove the two screws that hold the switch and remove the switch. Install the new switch like the old one came out and close it up you’re ready to go! It is very easy you can’t hurt anything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Debra from BLASDELL, NY
- Parts Used:
- W11429587
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
door catch broke
Remove the protective cover on door with screwdriver, pop out the old catch, snap new catch in place, replace protective cover
Was this instruction helpful to you?
Thank you for voting!