11077122310 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janice from Central Lake, MI
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt around the Lint Filter was loose and would not stay
Took out the old one and put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Rocky River, OH
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt on lint filter came off.
Just put the new lint filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Bluffdale, UT
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old filter screen was torn at edge of plastic rim
replaced with new one which had been improved upon by a brace down the middle of the screen.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ingram, TX
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint Screen Deteriorated
Replaced Lint Screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Oak Lawn, IL
- Parts Used:
- WP338906
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
No heat
I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Littlerock, CA
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
The flame periodically came on for 1 second.
Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Garden City, NY
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer worked but did not heat
Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.
Was this instruction helpful to you?
Thank you for voting!
The grill cover to the dryer vent broke in half
I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Nassau Bay, TX
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dryer does not heat
I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Quinn from Los Alamos, NM
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
Dryer would stat but no heat
The part came in very quickly. If you know how to remove the front panel, it is very easy to repair. The hard part is to diagnose the problem. The first thing to check is the igniter. If it comes on then you look for faulty limit switches. If you have lots of training in electronics and appliance repair this is very easy, if you do not I would not try this. I have 40 years in the repair business, It still took me 1hr. to find the problem. the switch was intermitted, one time the dryer would work the next time it would not. Good luck and happy repairs.
Was this instruction helpful to you?
Thank you for voting!