11077122310 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- JOHN from LAUREL, MD
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
right part easy
self...right part thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from Benicia, CA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed a lint filter
It was simply a replacement filter. No work just replace in slot. Thanks for great service and for sending in one day! We were shocked that the part arrived in one day! Will use your service again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from bristol, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
would not heat
changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diana from Nassau Bay, TX
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dryer does not heat
I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Beaverton, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would not heat!
After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Oak Lawn, IL
- Parts Used:
- WP338906
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set
No heat
I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.
Was this instruction helpful to you?
Thank you for voting!
The grill cover to the dryer vent broke in half
I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Littlerock, CA
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
The flame periodically came on for 1 second.
Since there were no troubleshooting steps, I had to start replacing the items according to the list that showed the parts that have fixed the problem for others. I ordered one at a time until I got the part that fixed the problem. I went through 4 parts before I replaced the gas solenoids which is what fixed the problem. By the time I was done, I could disassemble that dry in about 5 minutes or less.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Layton, UT
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lint filter tore causing hang up with metal guide
Removed lint filter cover (3 screws). Removed old lint filter. Adjusted metal guide. Reinstalled lint filter cover (3 screws). Installed lint filter. Replacement filter is a like quality.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from enola, PA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt came loose on lint screen.
ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from LANCASTER, SC
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced lent filter
replaced the lent filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly from Broomfield, CO
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt falling off of lint trap filter
Took the old one out and replaced with new filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Warren from Cedar Falls, IA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new lint filter
pulled out old lint filter. Put in new lint filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Phoenix, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
felt gasket had come loose!!!!
remove&replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cheryl from Waukesha, WI
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt liner on lint screen falls out replaced once from Whirlpool
My front- loading dryer is 4 years old and lint screen felt liner never lasted long without falling out. When I received my Part Select I knew the quality surpasses manufacture screen. It is so much better and we are your new customers forever Thank you Cheryl
Was this instruction helpful to you?
Thank you for voting!