11077122310 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mario from SAN DIEGO, CA
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No heat just tumble
Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Beaverton, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer would not heat!
After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Royal Palm Beach, FL
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Clothes were not getting dry enought
Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David M from Watertown, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Dryer would heat up for a short time, then shut off
First I replace the Radiant Flame Sensor, but the problem remain. Then replace the two coils and the igniter. Dryer works like it should. If I were to do it over, I would have replaced all 4 components to start with. Thanks for good advice and great service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- rick from Burton, MI
- Parts Used:
- WP338906
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Would not heat clothes dry
unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ambler, PA
- Parts Used:
- WP338906
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Dryer will not get hot
Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
The grill cover to the dryer vent broke in half
I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Plainfield, IL
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
No heat, therefore the clothes didn't dry.
I read some of the repairs of other people and this best described my situation. I ordered the Radiant Flame Sensor and followed the step by step instructions in the video for the repair, which by the way was excellent. It couldn't have been easier. My most difficult part of the repair was moving my dryer out of the laundry closet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Garden City, NY
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dryer worked but did not heat
Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marc from bristol, WI
- Parts Used:
- WP338906
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
would not heat
changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Tucson, AZ
- Parts Used:
- W10120998
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
bellow ripped
After trying to follow a very detailed description by another consumer, we googled our washer and found a site that showed step by step direction that took us through removing all panels and getting to the bellow easily. Not removing the proper panels, we found was making the job hard!I believe the site was applicance services...very helpful! Step by step literally!!Cost of parts through parts select reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- mary from enola, PA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Felt came loose on lint screen.
ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from LANCASTER, SC
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced lent filter
replaced the lent filter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Alliance, OH
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lint filter - The felt piece came apart from the screen unit.
My Daughter and I have the same washer and dryer from Maytag. Her felt piece came apart on the lint filter. I let my fingers do the walking and checked which filter went with the dryer and purchased it. When it got here, I made sure it matched up with the old one and just put it in the dryer where it belonged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathleen M from McDonough, GA
- Parts Used:
- W10120998
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the lint filter needed to be replaced
I took the old filter out and placed the new one in the same spot.
Was this instruction helpful to you?
Thank you for voting!