1106307807 Kenmore Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- juan from los angeles, CA
- Parts Used:
- 279570
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken door catch. door wont close properly
i watched the video from Part Select. did exactly as seen and presto it was easily done. never could've done it without Part Select.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from Carlisle, PA
- Parts Used:
- 279827
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set, Wrench (Adjustable)
Motor would run briefly then stop, then totally quit
Repair was simple, minus pulling the drive motor shaft out of the back fan. The female end of the dryer fan was made of plastic, so the socket wrench cracked the plastic end. Other than that, the repair was simple and easy to do. Much better paying the $88 for a new motor vice paying $400 or more for a new dryer. Dryer has run like a champ since replacing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- linda from las cruces, NM
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Lever was broke off
I used you-tube to troubleshoot and repair. Your part store was excellent to deal with. Delivery was prompt and cost was very reasonable. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Millinocket, ME
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Door would not latch
I pulled the old latch out of the catch and installed a new one. It just popped into place. The job could not have been easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michelle from Colby, KS
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My dryer door would not stay shut.
I removed the old door catch by using a screwdriver to pry it out, then I popped the new door catch in its place and it snapped right in. It took less than 5 minutes to do the whole job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Shortsville, NY
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the dryer would not turn on
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Carlsbad, CA
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer would not turn on, found metal clip in laundry
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.
*** Unplug machine ****
To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).
Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!
Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
*** Unplug machine ****
To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).
Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!
Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mike from Conway, AR
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer stopped working
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
Advice: Don't slam the dryer door. The actuator will last longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sally from Houston, TX
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
latch not working on Kenmore dryer
The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Perkasie, PA
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
replace the latch
take the old latch out and pop the new one in. Your repair kit worked perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matt from Stilwell, KS
- Parts Used:
- WP691581
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The switch in the door of the dryer was broken so it would keep running when you opened the door
I losened the two screws under the flap covering the filter or lint screen. With the screws removed the entire top of the dryer slides forward and hinges up allowing access to the door switch. The door switch is removed by taking two screws out with access obtained by opening the dryer door. Replacing the bracket/switch was easy and a simple reverse of the disassembly put the dryer back together. I would highly recommend doing this repair yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Edina, MN
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Part Broke Off
Took 5 seconds, just snapped in the slot, didn't need any tools.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Cincinnati, OH
- Parts Used:
- 279827
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
needed new motor
acyually need better instruction and a video of how to install. I did not tilt the motor so it was on a parallel with the drum and initiall had a thumping cause by the wrong location of the motor. Corrected that and it works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from North Aurora, IL
- Parts Used:
- WP691581
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer would not run.
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis from Riva, MD
- Parts Used:
- 279570
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
dryer door wouldnt latch shut
ordered new latch kit and repaired, very easy thank you
Was this instruction helpful to you?
Thank you for voting!