1106307807 Kenmore Dryer - Instructions

This was a classic easy repair and I am sure saved us bundles on a service call.

When I ordered the part, I viewed the installation video. That was a key step for me. It told me how to identify the correct part (there are multiple latch pieces in the repair kit, and one of them matches the type of door for the dryer), and how to disassemble the door to get the part installed. When the part came and I installed it, it turned out that I could snap the part in by hand, with no tools. It took about 5 seconds to try it, and it worked.

The dryer just stopped after a new load of clothes was put in. It appeared to be a power problem as there were not warnings, it just stopped. After checking the power, I suspected it was an electrical interlock problem. After nosing around, I traced the power to the dryer door interlock. Sure enough the switch was fine, but the mechanical lever was worn away. After Googling around for a replacement I found PartSelect.Com. Found the part, ordered it, and I am back in business. My wife is not happy though, as she wanted a new dryer:)

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

Read earlier posts on the change out of motor with times varying from 30min to days. My ordeal was in the days category. Long story short, I could not get the blower off. The back of the blower has flats to use a adjustable wrench and you can use a socket on the back of the motor. I rounded off the flats on the blower and had to cut it off. Since I had only ordered the motor, I had to then order blower. If you can get the blower off the motor is about a 30min to 1 hr job. I would suggest purchasing the blower along with the motor to save some time.

Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!

Was informed that I had a bad dryer motor and no warranty. Unplugged the unit. Removed to screws in the lint trap slot. Used a small blade screw driver to pop the 2 clips at the front of the dryer top. Lifted the top and rested it up against the wall. Removed 2 screws holding the machine front panel. Removed the front panel and removed the tub. Couldn't get the blower loose from the dryer motor so I cut it off with a hacksaw. Moral if you are going to replace the motor go ahead and by the blower too. It is less than $20.00. Popped 2 clamps loose holding the motor in and removed it. Placed the new motor in the unit. Strapped it down and attached the new blower. Plugged it in, put the dryer back togehter and tried it. It worked.

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

Repair was straight forward with only two screws to undo. Popped the two sides in and I was done. What was amazing was the lowest cost on parts and the timely delivery.

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

removed the broken part and replaced with the new one

Very easy to repair remove top of dryer and took out to screws and put switch back in place replaced screws and put top back on. Easy!!

I googled the problem, then came across a site where somebody had experienced the same problem, and they changed the door catches to resolve it. I did a search for Whirlpool parts and found "partselect.com". I followed the instructions on the website and located the parts very easily and also discovered that there was a video on how to make this repair. We were tolerating this problem for quite some time and now the problem is resolved, thank you...

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.