MHE15MNAZW International Dryer - Instructions

Door switch was very easy to replace as it simply snaps in for the outside and you just clip on the two control wires that already have clips on them.

Tools required: Stubby socket wrench, 5/16" socket, 1/2" socket, 1/4" socket, #3 Phillips screwdriver, external circlip pliers, straight slip joint pliers. A decently strong electric screwdriver is highly recommended - Milwaukee 2401-20 M12 cordless 1/4" Hex Screwdriver, for example.

Unplug the dryer. Turn off the gas supply.

Remove the screws holding the door hinges to the dryer.

Remove the door and hinges from the dryer by pulling the door and hinges up, then out.

Remove the two plastic thingies (door stops), opposite of where the hinges were, from the front panel of the dryer. Each plastic piece is held in place by two screws.

Grasp the front panel by its top edge, pull it toward you, then lift the panel up and off the clips at the bottom.

There are a couple metal brackets holding the top of the dryer down to the front shroud (the doorway) and frame, one on either side. Each bracket is held in place by two screws. Remove the screws, remove the brackets, then rock the top panel up and back, like the hood of a car.

Remove the screws holding the shroud to the frame. Look carefully. There are two screws that look like they hold the shroud to the frame, but actually do not. Don't remove these screws yet.

Remove the screws holding the plastic duct / lint screen slot to the shroud. These are very long.

Disconnect the wires from the door switch.

Remove the shroud.

Remember the two screws I referenced previously, stating they shouldn't yet be removed? Now's the time to remove them. Do so, then set the panel aside, being careful not to damage any wires. Don't lose the rubber gasket sitting around the circular portion of the duct.

There's a metal cover over the blower wheel. This cover is held in place by a bunch of screws. Remove them all, then remove the cover.

Remove the circlip going around the blower shaft, in front of the blower wheel.

Remove the clamp from around the blower wheel and shaft.

Pull the blower wheel off the shaft.

Install the new blower wheel.

Reinstall the clamp around the blower wheel and shaft.

Reinstall the circlip.

Reinstall the metal blower cover.

Make sure the rear of the drum is resting on the wheels.

Now things become a little difficult, because you have to fight the drum a little bit. Put the panel containing the moisture sensor, front drum seal, and duct into position. (Be careful not to mess up the drum glides. Make sure the rubber seal at the bottom of the vent is in place, sealing the vent to the blower.) Screw the panel into place with two screws, but don't fully tighten yet.

There's a felt seal that is supposed to go between the rear lip of the drum and the rear inside wall. The seal is supposed to be held folded, pinched between the lip and the wall, with the edge of the seal being outside the drum. The seal isn't supposed to jut into the inside of the drum. Use your fingers and some other tool to push the rear felt drum seal out of the inside of the drum. If you use a screwdriver, be careful that you don't cut, rip, or otherwise damage the felt seal.

Do the same with the front felt drum seal.

Carefully inspect the felt seals. You don't want any portion of the seal somehow working its way back into the inside of the drum. Then verify again that the rubber seal that goes between the blower housing and the vent is in place and properly sealing. Now tighten the screws.

Connect the wires to the door switch on the shroud, then loosely screw the shroud in place. Screw the shroud to the vent. Once all the screws are in place, tighten all the screws.

Lower the top of the dryer into position.

Hook a bracket into one side of the lid, position the bracket over the front shroud, then screw in place.

Repeat with the other bracket.

Place the front panel onto the bottom clips. Seat the panel onto the clips all the way, then rock the panel forward into place.

Install the plastic door stops.

Insert the door hinges into their slots, push the door down to seat into place, then install the screws that hold the hinges in place.

Plug the dryer in, turn on the gas, test.

I removed the control panel and front panel, then the brace holding in the drum. Then the drum came out easily.

Replacing the rollers is easy, use circlip pliers to remove the old circlips, replace the rollers, and reinstall the circlips.

After removing the idler pulley by removing one bolt and the spring, I replaced the idler roller, again with the circlip pliers. Then the idler arm bolts back to the motor mount, and the spring is replaced.

Reinstalling is easy - place the drum, have someone support it while you install the drum brace, then replace the front panel, then the control panel.

Went smoothly. Took the opportunity to vacuum out entire cabinet. Also removed tumbler vanes inside dryer as coins had made their way into them. The only other suggestion I have is that I didn't notice cabinet screws were different lengths till I started reassembly. Might be smart to label and separate them

Followed the directions on the video. I recommend changing both tumbler wheels and idler pulley when you have unit apart as well as the drive belt. When I opened the dryer cabinet I immediately saw what my scraping noise was being caused by. A screw holding a baffle in the dryer tub had backed out and was scraping the cabinet wall on each rotated pass. Like I said, when you have the cabinet apart you might as well change parts that are going to fail. The repair was very easy and now I have many more years of service with my dryer. Had I opened the dryer before to see what parts I needed I would have seen the loose screw.

Disassembled dryer and replaced drum support roller and shaft. That took care of the noise but I still replaced the belt and idler pulley while I had it apart.

I looked at this website and found the symptoms, noisy, and no heat or not enough heat. I ordered the recommended parts. They were the drum support roller kit, idler pulley wheel and bearing, high limit thermostat, and lastly the front glide kit. I had anticipated having to use all of these parts. Upon following the instructions in the videos (couldn't ask for better instructions) I disassembled the dryer to see how bad everything was before replacing the parts. The left drum support roller spun easily, but had a little roughness and slight noise, the right one spun easily but not like I thought a new one would have spun, the idler pulley was stiff and very noisy. The thermostats all seemed to be in good shape (had continuity). I cleaned the bearings and shafts of all of the rollers with alcohol, paper towels and cotton swabs. The bearings and shafts all looked like new, so I lubed them with a slight amount of high temperature grease and reassembled the rollers. They moved smoothly and quietly. The fan was quite full of lint, even cleaning the filter after every load does not stop all of the lint. It has been in use probably over 10 years. After everything was back together, it runs like a well oiled sewing machine and has been drying well. I did return the parts unopened. This would not have been so successful without the videos. Thanks to all of you.

All you need for a Maytag is a snub nose Philips screw driver. The screws on the front panel are at the bottom angled down, so a regular length Phillip's won't work. Just unscrew the 2 screws, then lift the panel up and out. Careful not to pull out too far, there are 2 wires attached to the switch. The replacement switch is NOT an exact copy of the old one. My Maytag is over 30 years old and it only had 2 prongs on the switch. The new one has 3. Don't let that throw you. It is the same size. Just attach, 1 wire to the bronze connector & the other to the silver. Push the switch into the door opening, re-attach the door. Total time 20 minutes. Saved well over $100 in a service call. Anyone with an IQ above freezing can do it.

I looked up my problem online and everything I saw said to change the roller wheels that hold the barrel of the dryer. After doing that (twice, once on each side) I was still having a horrible squeaking sound so bad that we were waiting to do laundry until we were leaving for a while. Finally I determined that the problem was actually the idler wheel. All I had to do was remove the bolt holding the idler arm on (it's the arm that has a spring connected to it that moves to allow the belt on or off) and put the new arm with the new wheel on. The dryer is now whisper quiet and works perfectly.

Replaced both rollers,shafts, bearings and snap rings.

The YouTube video on how to replace the baffels was excellent. After watching the video, it was a piece of cake.

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

I had replaced belt, but the noise continued. Ordered new rollers and washer. Removed the front panel by tipping the dryer back against the wall and removing two screws at the bottom of the panel. Tipping the dryer makes it easy to remove the front panel. Removed the front drum support by removing four (4) screws. I was then able to just move the drum enough to have access to the rollers. Didn't even have to remove the belt. Replaced the rollers. Needed special pliers to remove and replace the retaining rings. Put the drum back into position and mounted the front drum support. Tightened four screws and then put the front panel back on. Plugged it in and tested it. Problem solved. Took about 35 minutes. Thanks

Took off front. Removed door. Removed drum support. Removed drum and belt. Made sure motor was correct size and fit. Removed blower wheel. Disconnected wire plug from motor and slid motor out of blower wheel. Replaced everything in reverse order. Figuring out belt tensioning position was a trip, but finally got it. Vacuumed out all the lint. Amazingly it worked!

Piece of cake. Use the available manual to ascertain dismantling procedure. Only thing that might be tough for average DIY'er is the internal snap rings. Snap ring pliers are mandatory for quick easy repair.
Total time was probably about 15 minutes and this was the first time I had taken it apart. Quiet as a mouse now!
Very helpful site.