MHE15MNAGW International Dryer - Instructions

Unplugged the unit
Removed door and two clips that hold front panel on (6 Philip crews)
Then removed front panel by hand hold each side of the panel at the top
Of the “U” shape and pulling out ward until it frees it self from the two
Bottom clips.
You can now see a belt that is no longer tight around the drum
When I tried to put the belt back on I noticed the idler pulley was flopping around and I would need to replace it .That where you guys saved me.
Your exploded model and parts list made it easy to see exactly what parts I
Needed to order.
The rest gets a little tricky there is another plate that supports the barrel
A couple of clips that hold the top cover in place all of this must be removed
Note the top cover only need to be lifted up an inch or two at the front where the
Two steel clips where and doses not need to be removed to get this panel off that
Supports the barrel.
There are some wires attached to it also I only had to unplug the three that go to
The door safety switch then I was able to rotate it off to the side out of the way
And now the barrel can be lifted out. You can now remove the idler pulley assembly
I used pliers to remove the spring and a crocket wrench to remove a bolt that holds
The bracket that also should be replaced due to ware at the idler pulley barring pin
The tricky part is putting it all back together again. To explain this I would need to Wright a book. It takes a lot of good common sense. I was proud of how I reached
Around from each side of the motor and by feel alone and get the belt around
The motor pulley and the idler pulley that keeps the belt tight around the barrel
Makes me think I should have been a repairman.

I set the dryer on its back to make alignment of the front drum guide cover easy to reinstall in the seal after completion. I removed the 2 screws at the bottom front then removed the white and yellow wires to the interlock switch and set the front cover aside. I then removed the 4 nut screws holding the front drum cover and removed. On the back side there are two teflon and cork "bearings". I had ordered two even though only one was worn down to metal. On each one I then removed the two rivets by drilling them out. Then I placed the corks into the bearing slots with a little glue then inserted the teflon into the slots and riveted them into place with the rivets that came with the kit. I replaced the drum cover, connected the switch and screwed the dryer front cover back on. I set the dryer back up. Connected the vent hose and turned the dryer on. Beautiful sweet smooth and quiet operation. I had replaced the front and back drum seals a few months ago and saw the teflon was missing but did not have the kits at that time. With a complete job I would recommend replacing the front and rear drum seals and the two teflon/cork bearing kits at the same time.

This was pretty much as easy as most other folks had described on this site.
1. Removed the two screws at the front bottom that are holding on the fromt panel, and then lift up and remove the panel.
2. Disconnect the door-open-safety-switch, remembering which color of wire goes on which connection.
3. Remove the four screws (two on each side) on the front bracket that supports the drum and tthat contains the front glides.
4. Remove support bracket and lint trap, letting the drum rest gently on the stuff underneath.
5. Remove the screws holding the lint trap to the support bracket. (My model had five screws.) Remove lint trap from support bracket.
6. Drill out the two pop rivets on each of the two glides, noting the orientation of the teflon pad and mounting strip.
7. Secure - and here is where I had a little problem - new glides in place with pop rivets. (I hadn't use a rivet gun in a while, so I messed up the first pop rivet and had to go to the hardware store to get a replacement. I didn't hold the pop rivet in all the way while I was accuating the gun!)
8. Reverse the process for assembly, and you are all done.

It's simple.

Old latch and door striker were pried out with a flat blade screwdriver. New components popped right in. Repair was less than two minutes.

I inserted the clip

1. Remove 2 screws that hold door hinges on.
2. Remove 2 screws on opposite side of door hinge and remove 2 plastic clips.
3. There are 2 hex screws that hold the front panel on. Remove these and the panel is held on by a flex clip. Gently twist the top towards the outside of the dryer and they will come free.
4. tilt panel forward and lift of 2 clips at the bottom.
5. Remove the screws under the cover panel which will release the drum holder and lint collector.
6. Lift top of dryer and lift out drum.
TAKE THE TIME SINCE THE UNIT IS OPEN TO VACUUM OUT THE ENTIRE DRYER. CLEAN OUT THE EXAUST TO IMPROVE EFFICIENCY AND SAFETY.
7. I replaced the rear felt by using a flat head screwdriver to lift tabs and install felt. Using the screwdrive I compressed the tabs to hold the felt.
8. The baffle was installed inside the drum and using 2 hex bolts to hold the baffle in. I added 2 washers since the hole was inlarged due to the baffle becoming loose and pulling through the metal drum.
9. Re-install the drum and push rear felt to the outside of the drum.
10. The front drum needs to be installed. Push the felt to the outside of the drum and check the rear felt to ensure it is still on the outsid of the drum. Install 4 hex screws to secure front drum holder.
11. Insatall lint catch unit with 4 additional hex screws.
12. Verify the lint collection panel lins up with the exhaust fan at the base. When units line up tighten all 8 hex screws.
13. Reinstall front cover panel by inserting panel on bottom clips and tilt up to the dryer. The top corners are gently twisted to the outside of the dryer to reattach to the spring clips. Use 2 hex screws to attach panel.
14. Re-attach plastic clips and 2 screws on side opposite of door hinges.
15. Re-attach door hinges with 2 screws. Cleck to ensure the door closes.
16. Check dryer operation.

Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well

took old one out then i had to strip the connector off new one was to big...

Had to remove the dryer door and back top screws to access the drum.
Once this was accomplished all that had to be done was to turn the drum by hand and replace each baffle and (two) screws each.

After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.

Press in the new female latch part with thumbs. Took about two seconds!

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

I watched the video

Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!