CDM2000RW459 General Electric Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- allison from exeter, NH
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob broke
popped the new one on, and works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Mansfield, MA
- Parts Used:
- WE11M23
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
dryer was not heating up
Had to remove the drum to get at the heater element also had to swop the sensers to the new element
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elbert from LAWTEY, FL
- Parts Used:
- WE25M40
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Dryer Squeeky
Watched the video on YouTube and everything went great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JEAN from POPLAR GROVE, AR
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
selector knob was striped out
Just took the old knob off and put the new knob on. It was a snap. Thanks you very much
Was this instruction helpful to you?
Thank you for voting!
broken door strike and latch
Parts arrived well in time, exactly what was needed. The latch was a snap-in process. The strike require gentile use of a pliers, and went in quickly. Thanks!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rita from Cape Coral, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic selector knob on front of dryer cracked
new knob fit onto 'd' shaped spindle. This took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nate from Affton, MO
- Parts Used:
- WE11M23
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Dryer runs but does not heat
My dryer would run but not heat and the timer would not advance. PartSelect helped me determine that the heating element needed to be replaced. I have very little experience with appliance repair. I found this to be challenging but well worth it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jean from Waterford, MI
- Parts Used:
- WE1M1011
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The dryer door wouldn't stay closed.
There is a plastic female closure part in the dryer door that wouldn't close tightly around the metal male closure on the dryer. I popped out the plastic square with a screwdriver, popped the new plastic closure in with my thumb. Works great. I never even installed the new metal portion of the latch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michell from Bellefontaine, OH
- Parts Used:
- WE25M40
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Loud Sqeaking noise
the replacement part was easy to replace but remembering how the belt went back on took alittle more time..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fawn from Loganville, GA
- Parts Used:
- WE1M1011
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer door would no longer shut.
Simply popped the old broken part out and popped the new part into place. I wasn't sure if it was the Latch Door or the Door Strike. Once the parts arrived, it was clear the Door Strike was not the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- June from Port Charlotte, FL
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
It was only a matter of putting a new knob in place of the broken one. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Bakersfield, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Dryer Start knob broken inside of stem.
Knob stem was split, leaving the metal bushing on the dryer's Start switch. Used pliers to remove metal collet. Aligned new knob to switch, and firmly pushed replacement part into place. Tested results and found it to be satisfactory.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Upper Marlboro, MD
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken dryer selector knob
I opened the box which contained the new selector knob. Placed it on my dryer and immediately turned the knob to start the dryer. Easy steps to follow the video supplied when i ordered the part. I am greatful you responded to my order within 3 days. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Orange, CA
- Parts Used:
- WH1X2721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
Simple replacement. Very easy.
Was this instruction helpful to you?
Thank you for voting!