CDM2000RW459 General Electric Dryer - Instructions

An easy fix. I was impressed with how fast I received the parts!1 Three days and that was during Christmas mailing season. I was very satified. Craig H. Tampa Florida

ordered a knob for my dryer. snapped it on. simple.

The knob to start my dryer broke about a year age. I was using pliers to start the dryer. I was sure I would never find a replacement part and it was just a matter of time before the plier trick would break the start knob. I decided to look on line for a replacement knob sure that I wouldn't find one. Clicked on PartSelect, enter General Electric dryer and a bit more simple info and there was the part I needed. This site has everything. My dryer is good as new. Thanks PartSelect

The pictures really made it possible to determine exactly which knob was what I needed for my dryer. Thanks.

The start knob had crack in it that was getting bigger, and we'd begun using pliers to start it. Not only was it unwieldy but I thought it would eventually strip the metal stem. Of course this was a breeze of a repair--we just slid the new knob on. But my husband had been certain that finding a replacement knob--or calling a dealing and ordering the part--would be a big deal. I said: "But let's just try on-line." We quickly found the model # inside the dryer door. We filled in the appliance info, the part popped up. I ordered it. It arrived in 2 days. It's like new.

ordered replacement. received in two days and voila! Fixed!

pulled off the old knob and replaced it with the new knob.

Ordered a new knob and replaced the broken one.

plug new knob.

it was easy, it clip right on.needed to give it a little tap to get it in .

First of all, I am a women...I read where it was probably my rear bearings so I ordered the part, it came in just right, then I replaced it put it all back together, and with the computers help, got it going, belt back on and all and then turned it on and walah it still made a loud noise. Shucks, so I read more and it said it could be the front bearings which I should have tried first but didn't read it first. Ordered part and put it on and wallah, that wasn't it. The noise sounded like the paper in a bicycle spoke so I checked the fan. There was the problem. The fan had so much dryer lint behind it it was forcing it against the housing making a noise. Cleaned it removed all the new unnessary parts and re-boxed them and put it back together but just before I put it together the door fell and two wires came loose so I plugged them back in and put the wrong one in the wrong place cause when I plugged the dryer in sparks went everywhere!!!! I need a man now!!! Scared of electricity!! Sure wish I knew if the noise was fixed :).

First I removed the drum as described in many other comments. Took me about 10 minutes, pretty easy. Replaced the part which was easy and could be figured out just by seeing how you took the original part off. The hard part was aligning the drum, drum washer, and metal plate back into the drum bearing. I tried over 2 hours to do this and because it rotates and it's almost impossible to line up all the holes, I decided to do it another way.

I took apart the drum bearing from the back panel and then outside of the dryer walls I aligned the drum, washer, metal plate and drum bearing. I screwed them all in together and then, went into the frame and reconnected it at the back w/ the horseshoe looking washer. It worked perfectly and I was frustrated that it took me so long to figure out a different way to do it.

I have to say because of the installation it was a little tough than anticipated but was very happy with the end result (no squeaking) and money savings. Definitely worth giving it a try if you're patient.

It was simple to get drum out. I took all screws holding top and door out with out problems, then released the drive belt. It took some wiggling to get the drum out. I then was able to get at the rear elements. Taking the wires off the thermostat came off with a little persuasion. Removing shaft from drum took some stretching as I was doing the work by myself. I would suggest that a helper be used for the removal and replacement of the shaft. Reassembly was easy. Just reverse of the above.

nd removed it from the unit.
5. replaced drum bearings
6. reassembled everything in the same order I took it off.

Be sure to mark any wires you may disconnect to ensure you connect them back correctly.
Was a bit frustrating at times, but made it through and there is no more squeek.

The knob had broken off a few months ago. I didn't think to look for one on the internet. I finally googled the brand name and part number and your company came up. It had the picture of the part which I ordered immediately. It came in the mail really quickly. I was so excited when I received the knob. I took it out of the package and slipped it over the stem in less than a minute. It went on perfectly. Now I no longer need to use pliers to turn on the dryer. It looks great and I am no longer inconvenienced. I love the new knob and would do business with this company again.