PTMX910GMWW0 General Electric Dryer - Instructions

Unplugged power. removed 2 screws to take of top cover. once inside removed 2 more screws to slide front panel of. I first replaced slides on front panel. I then lift drum and installed new belt. Only trick is to make sure you wrap belt around tension arm pully properly. Basically a very easy job

When we first heard the screeching i thought right away that it was the belt. we ordered a new one and after i replaced it the dryer was still just as loud. I wished i went here first. Right away i found others with the same problem, did the same repair which was just taking 2 screws out, sliding the top and front panel off(watch for the electric wire connected to the panel) and replace a couple of plastic slides. now it is better than ever.

had a great video to follow, made it easy to install.

YouTube showed me just what to do. I unplugged the dryer and took the back off. Then I took a picture of the timer with my phone since there were about 6 different colored wires that had to be unhooked and put back in the right place. It was not difficult. Last I turned the timer in the bracket so it was secure. I also had to order a new dial since the old one was split from years of use. A repairman would have charged for the call out plus the parts so I saved money by doing it myself. P.S. I'm a 71 year old woman.

Open Door /remove 2 screws in top of door opening (this releases the top panel) /Lift top panel off of dryer (it is tucked under control panel) Remove the white plastic "arch" (front drum bearing) on top of door panel / Install new drum bearing and 4 each of the "slides" on the bearing/ There are two on each side of the "front drum bearing"/ Reverse the disassembly process to finish/ . You'll need a standard flat tip screw driver and a Phillips heads crewdriver to do all work

easy to fix took less than 10 minutes

Removed the broken lint filter and replaced with new

It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.

I remove the know, slid the old timer out, leaving the wires connected. Placed the new timer into position and secured it, then unplugged wiring one at a time, placing them onto the new timer. All went great.

looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.

Based on the few components in a dryer, I diagnosed the problem as a defective timer switch. Five screws remove the rear cover. The timer switch purchased was the identical part that was currently installed. In the old days, I would have drawn a picture to note the wiring connections. These days, we just take a picture on a cell phone. I removed the switch from the dryer and moved the wire connections one at a time over to the new switch. When all of the connections were in place, I installed the new switch. With cover still removed, we tested it and the dryer shut off as it should. Super easy repair. The only thing I would have done differently is I should have purchased a replacement knob and retainer - the original had cracks in the plastic that I didn't know about until re-assembly. Superglue took care of the knob, but I should have replaced it too. Disconnect the power cord first, take your time, and be careful with the sharp edges of sheet metal. I suffered an ugly cut on my finger but I'll survive. Super easy repair. She'll think you're a hero since she didn't have to call a repair man.

Easy peasey! Just Removed/Replace screw-in type bulb.

Removed the star bit screws on the top of the control panel then removed the front by opening the door and removing the screws in the upper corners of the door jam. I then removed the top which exposed the drum slides. NOTE: This model requires 4 drum slides and NOT two as specified in the video.

First I watched the repair video on partselect.com and that really helped. It was really easy to replace the slides. I even ordered a new top bearing, old one was busted, and replaced it. Thank you for your help.

Removed top panel giving access to drum and screws that hold front panel (door). Removed to screws to be able to remove front panel but be careful wires are short not giving you much room to remove panel. Removed plastic Drum Bearing and replaced with New one. Installed slides and put back together.