PTMX910GMWW0 General Electric Dryer - Instructions

looked at video of dryer disassemble, replaced 4 bearing slides, reassembled. Dryer is perfect now , no noise. thank you for your parts.

It was so simple. I removed the old ripped gasket by just pulling it. I followed the same direction with the new gasket by using a small screw driver to push in the tabs in each of the holes in the door. It works perfectly. They only fear I had was getting the part and the correct part, the model number of the dryer was on the door which made it easy.

I remove the know, slid the old timer out, leaving the wires connected. Placed the new timer into position and secured it, then unplugged wiring one at a time, placing them onto the new timer. All went great.

Opened up dryer for access to all components and tested. All checked good. Put back together and tested and igniter came on but no flame. Purchased two new coils and tested again. No flame. Purchased complete valve assembly and replaced old one. Tested again and viola, success! TY PartSelect for exact replacement part.

good replacement procedure on you tube.

On my GE Dryer the lint filter is located inside the door at the bottom. The filter can just be pulled out by hand & a new one pushed into place

First and most important - safety. Either unplug the dryer or shut off the circuit breaker. Remove the two screws to the top cover. To locate these screws just open the door as they are located at the top of the door opening. Remove screws and lift up the top cover and carefully pull towards you. Place to the side away from the work area. This now will expose two screws within the side panels holding the front door and front housing. Remove the two screws, lift up and out to remove front housing assemble. Be careful when you remove as the wiring to the light fixture is included. Just remove cover and place side ways close to the dryer.
Remove the bulb then remove the white plastic drum bearing (snaps out or in when replacing with a flat screwdriver).
Prior to installing the new drum bearing install the four white slide strips on top of the drum bearing. Review the old parts for comparison. These actually act as the bushings between the drum bearing and the clothes drum. Please keep in mind the slides do not come with the drum bearing when ordering. You must order seperately. Once the new assemble is snapped into the metal front cover/door now you can re-assemble. While you have the drum exposed it's a good time to check the belt for wear. Sometimes a worn or ripped belt can be the same symptom of the thumpimg sound. For the assemble just reverse all the earlier steps. Plug cord back in or turn on the circuit breaker and run the dryer. You should be good to go for more years of service.

Removed too of dryer and placed the parts on. Runs like a brand new one. Thanks so much!

the pulley spring took so much pressure to hold it down it took 3 men and a boy to hold it and place it in position to to get the belt on. Also there is not enough room to get your arms and hands in without getting some small cuts.Ultimately I removed the screws in the back of the dryer and spread the side of the dryer out to gain proper access. It was an easy repair if the spring would not have been so strong.

First I replaced the timer, but dryer still did not start. took apart dryer, jumper out door and componet near motor to see what problem was and to be able to run dryer while opened up. Actually motor had seized up just enough to not allow motor to start rotating. Lubricated motor shaft and rotated motor for oil to work its way in. Tried starting again and motor started. Buttoned dryer back up and reconnected wires to appropriate places and started dryer again and again.Worked for 4 loads of laundry and still working for 3 loads on Wednesday. Working fine

First, I unplugged the dryer, pulled it out into an open area. I then removed the vent hose. I opened the front door and removed the 2 screws that hold the top panel down. Once removed, I lifted off the top which exposed the drum. Next, I remove the 2 screws along each side that allows the front door panel to detached. I noticed that there was damage to the plastic bearing and 3 bearing pads were missing. That was the source of the noise. Once the door panel is lifted off the cabinet, the wires to the safety switch must be pulled off so the door can be set aside out of the way. Then I went to the rear and remove 2 more screws that gave access to the motor, wiring and the tensioner for the dryer belt. Once I gained access to the belt, I slipped it off the tensioner and drive pulley. This allows the drum to be removed from the cabinet. WE wrestled the drum out before realizing that we should have removed another 2 screws securing the sides of the dryer to a cross support under the front of the drum. This would have made the removal of the drum much easier. Once the drum was removed, I had access to the heating coils. Upon examining, I saw that both had burned out at the far left terminals. Directions that came with the new heating elements gave clear instructions on how to install. It's a little daunting to thread both elements through all the insulators, but patience paid off. Everything went back together easily and the dryer started up and heated up just like new.

I replaced the dryer bearing ( a plastic part) and all of the slides on the bearing. It now operates like new.

Removed gas line. removed control panel, removed top, removed front, removed burner, replaced igniter, put back in. paused and played the video. very easy to do. 42 minutes and I had a few beers.

Replaced new screen in place of old one.

Wife was out of town, visiting family. I broke the door strike by wedging the dryer door between the laundry room door, closed the laundry room door and it snapped the door strike breaking it. I ordered the part, and it shipped fast using the standard shipping, nothing fancy. Grabbed a pair of pliers and pushed the new door strike into place. It snapped right in, fits and works perfect like nothing ever happened. The wife will never know :)