DDG8205NC General Electric Dryer - Instructions

I opened the top,by removing the two screws inside the door
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.

Replaced gas igniter The part came a day after I ordered it. I really liked the speed of delivery.

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

My Daughter did it for me .

Unplug the dryer, turn off the gas. Opened the lower front door panel. She disconnected the gas pipe from the igniter assembly. Then She removed the two screws holding the assmb. Then she removed the wire from the front of the assmb. and the white and black wire from the back of the unit. remove the old igniter put in the new one put it back together.

Followed an online website, removed the top, front, two rear access panels, disassembled the spring clip from the rear of the drum, took the belt off of the motor, removed the drum, took the rear bearing support out, replaced the bearing and reassembled the dryer.

I was disappointed that there were No Instructions included with the part. So I found a you-tube video that wlked me through it...Took off back of dryer, then the top, then the front to get to the igniter...could not pull out the part, so I had to reach in and replace it while it was in the dryer. It Works!

Unplugged dryer. Removed access door from lower right front of dryer. Disconnected wiring harness to igniter. Couldn't reach retaining bolt with wrench or socket, but was able to spread igniter clip with fingers to be able to remove old igniter and then work new igniter into position without unbolting retaining clip - ultimately a tool-less operation that could have taken 5 minutes. Reconnect wiring harness and reconnect power. Test dryer then replace access cover.

I watched Youtube videos on how to troubleshoot the dryer but I did not go through all the testing of the fuses and the heat sensor. I did not want to take the dryer apart if I didn't have to. I turned on the dryer and looked into the bottom grate and saw no glow from the igniter (it should be very bright) so I started there. (The Youtube videos test the igniter last). Unplug the dryer. Turn off the gas. Pry off the grate. Unplug the igniter connector and set the multimeter to tone on continuity. There was no tone so it was bad. I used a flashlight that I put inside next to the gas valve to see. Remove the top flat cover on the burner assembly, 2 screws. (Had to do all this laying on my belly in front of the dryer. Very uncomfortable.) Remove the old igniter from the clamp. It fell apart as I took it out. Now the tricky part: The clamp is very tight and the igniter is delicate. I tried to slide it in from the top holding it between my index and middle finger and lining up the slots for the igniter 'wings'. I struggled with that until many-swear-words-later, I decided to slide the igniter in sideways. Put the 'wing' into the clamp's left side opening and then gently but firmly squeezed the 'barrel' into the clamp. It worked. Plug in igniter plug, put burner cover back on carefully without banging igniter, turn on gas, plug in dryer. Turn on dryer. Igniter should be very bright when it lights. It takes a little while to heat up the heat sensor that will open the gas valve and the burner should light.

Unplug dryer and turn off gas to appliance. Remove small vent door front of dryer for access to burner assembly. Reach inside and remove all three wires attached to the valve. Using a backup wrench remove the union that attaches the 3/8" gas line to the burner assembly. Remove the two bracket screws holding the assembly. The entire burner assembly can now be pulled out. Replace the faulty igniter by spreading the retainer clip and inserting the new part. Use extreme care not to touch the new igniter with bare skin...best to use a helper to assist holding the assembly while you insert the igniter. Then replace everything as you found it . Soap all gas fittings, plug it in and enjoy your dryer.

Researching on the web I thought the trouble might be lint buildup or trouble w/ one of the parts involved in spinning the drum. However I cleaned out all the lint and replaced the belt and idler pulley and this didn't improve the smell (drum bearing was fine). I then concluded the trouble was the motor. Running the motor w/o the drum in place confirmed this was where the noise/smell was coming from. Replacing the motor was fiddly--I had to remove the clip holding the motor (pried the top w/ a screwdriver), wires (made a diagram so as to put back in same order, they were hard to get off--a pliers did the job), clamps holding the motor on the duct, the motor mount, the duct, the fan. Putting all this back together took a while (not hard just fiddly). Tested the motor w/out the drum in place and it sounded fine. Put the drum and back/front/top panels back and the dryer runs fine now. All parts came quickly and exactly matched the parts in my 1993 Hotpoint dryer. As others have said the pulley kit is not needed--these are included w/ the motor. BTW I am a 53-year-old lady. Thanks to all who took the time to write up their experiences--big help!!

followed video direction ,pulled part ,compared to part on-line ,ordered part delivered in two buisness days and installed ,back in service .very simple and I will shop at your sight again and tell friends and family as well

Break up the broken knob easily with plyers.Once thats off then push on the new knob with your fingers that took 3 seconds ,fit perfect.

Removed two screws from front by door. Removed back panel to remove belt from tensioner. lifted lid of dryer. removed two more screws from inside to remove front panel. while holding the barrel I removed the front panel then grabbed barrel and pulled out. took off the old bearing, put the new one on and reassembled it the way I took it apart. The whole thing took about 10 min was quick and easy if there is any problems while you are doing it look it up on youtube.com and you can see it done.

the switch was stuck couldn't get the switch to pop out to stop the dryer when opening the door light inside also wouldnt go on. it only took a few min to take it the switch and replace the new switch the light now works also stops when opening the door it made my day easierhow easy it was to fix it. only take to use a pliers and screw driver.

The info from your web site was helpful. I had never taken a dryer apart and the instructions made the job easy. Used socket set to remove the back panel and top control panel. Then used a phillip's screwdriver to remove the two screws that hold the top of the dryer; these screws are accessed by opening the door to the dryer. To remove the front of the dryer remove to the two screws that are located at the top upper corners where front panel meet the side panel. Once these two screws are removed, remove the belt from around the drum and lift the drum out. The drum bearing is located on the back of the drum; remove the remnants of the old bearing and replace it with the new one. Retrace your steps to put the dryer back together. To get the belt back on track you will have to remove the lower back panel to access the belt drive and tension pulley. It is not difficult. God bless you.