Models > DDG8205NC

DDG8205NC General Electric Dryer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing – Part Number: WE3X75
$18.69
This part is the rear dryer drum bearing only. This part helps keep your dryer running smoothly as possible with as little noise as possible.
In Stock
Gas Igniter – Part Number: WE4X444
$49.67
Be very careful to not handle the igniter by its gray part. Hold it by its white tip only.
In Stock
Drive Motor – Part Number: WE17X10010
$348.87
Replaces "T" and "V" style motors. Includes two motor pulleys. If you have an older model dryer, the pulley may be pressed on or held on with a set screw. If pulley is pressed on, a new motor pulley must be ordered.
In Stock
Door Switch – Part Number: WE4X197
This part has three terminals. Note: Use the two smaller terminals for models that only have two wires to the switch.
No Longer Available
Blower Wheel – Part Number: WE16M15
$74.16
This wheel attaches to the motor.
In Stock
Timer Knob – Part Number: WE1X1266
This knob accepts a D-shaped shaft.
No Longer Available
Multi Rib Belt - 4 Ridges – Part Number: WE12X49P
This dryer drum belt goes around the dryer drum and the pulleys to rotate the drum once motor is activate.
No Longer Available
This 'K' series three-coil coil kit fits older model GE clothes dryers. It comes with the wiring harness and the igniter bracket.
No Longer Available
SLIDE Assembly – Part Number: WE13X93
$41.19
Special Order
LINT FILTER – Part Number: WE18X34
No Longer Available
DISCONTINUED – Part Number: WE12X45
No Longer Available
THERMOSTAT – Part Number: WE4X325
$27.96
Special Order
View More

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for DDG8205NC

Viewing 1 of 1
Noisy
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Replacing the Drive Motor

Replacing the Drive Motor

Replacing the Blower Wheel

Replacing the Blower Wheel

View More
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jeff from Seattle, WA
Parts Used:
WE4X444
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench set
Gas dryer heat would not come on
Unplugged dryer, opened lower panel. Loosened the bolt that holds igniter assembly to gas unit and removed old igniter. Put new igniter in the pinch clamp then (being VERY careful so as not to crack new part) replaced igniter assembly and tightened its bolt firmly. Voilà, ignition!
40 of 58 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Virginia Beach, VA
Parts Used:
WE4X197
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
replqce bad switch
pried old switch assembly from front of machine with screw driver. removed 2 electrical connections. shorted terminals to verify problem. inserted wiring terminals to new switch. verified operation and then pushed switch assembly into machine opening.
30 of 33 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOE from Galion, OH
Parts Used:
WE3X75
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Old drum bearingwore out, squeeking like a banchee
Received part in two days.
Removed inspection plate by removing two screws. .Drum bearing was right there. With screwdriver
removed "c" clip, took out what was left of old bearing.
With screwdriver aligned drum, slide new bearing into place. Job was done. Instruction with new part simple and easy to follow.
17 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More