UAN7214C Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Bells, TN
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Loud squeeling noise
I had trouble with the little piece on the back side of the dryer not lining up with the bearing housing. I also didn't see how the drum was gonna stay in place but finally realized the front cover lines it up. All in all it was awesome to get the part I needed so quickly and cheap, thanks a lot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from cherry hill, NJ
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
rear bearing failure
after cutting the power, I used a putty knife to release the two holding clips ot remove the top,, 2 foward facing screws on either side of the front and two cap covered screws holding the bottom and unhooked the two electricial connections for the control panel and removed the front panel. Since this was a stack unit and in a closet most work had to be done from the front. By reaching inside to remove the belt from the motor,removing the drum was the easy part, to get to the bearing, but unfortunatly I had to remove the dryer from the closet to replace the back bearing clip and ball. After that replacing the bearing bracket and housing it was a breeze. Getting the unit back in the closet was a slight struggle, but it all worked out for the best got a chance to cleas behind the dryer, and the repaire was successful, phew.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from New York, NY
- Parts Used:
- 5308015435
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The knob of my dryer broke
I had a repair man fix it- it went very well
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryant from tolna, ND
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer did not turn
put the new part on with ease took 5 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Angelique from Metairie, LA
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The door could not close due to a problem in the latch
I replaced the latch on the body and on the door and it worked very well. I had to watch the video first. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jurg from Los Angeles, CA
- Parts Used:
- 5303212849
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
Old roller worn out
It was really easy to install the new roller with the newly designed side flange! All I had to do is hook in the tension spring. Works perfect again without the squeeking noise!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ron from waynesboro, VA
- Parts Used:
- 5303281154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken Belt...measured 88" x 1/2" flat belt
The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Lindenhurst, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Old bearing made noise. Grease was dry and worn out.
The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruce from Roscoe, IL
- Parts Used:
- 5303281153
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Scraping noise at rear of drum
Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amy from salem, OR
- Parts Used:
- 5303281153, 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The Rear drum bearing kit had sheared off
Exactly how the video showed! It was super easy and I am a girl...although I am a lil more mechanicly inclined than most girls, it was a piece of cake!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Witly from Wheatley Heights, NY
- Parts Used:
- 5303281153
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The only probelem was to take out the drum, because it was a washer and dryer combo. the dryer was on top, i did not have any room to pull out the drum
I remove the drum, and install the bearing just like the instructions in the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jason from Grandview, MO
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
latch assembly popped out partially on door and when it shut it broke the catch on the dryer.
Popped in new catch and used needle nose pliers to squeeze old latch flat and remove from door. New one just popped into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from Brookfield, OH
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic Catch broke and door wouldn't close
Another parts website, instructed taking apart the dryer top and front and electrical connections etc. I thought I'd have to buy a new dryer!. Then I found your website, and I was laughing so hard, because your instructions were so simple and logical and took me under a minute to do the "repair". I used a plastic ice scraper instead of a metal putty knife (so as not to scratch the finish) to pry out the broken part. Then using my fingers on one hand I pushed in the new part. I closed the door to make sure the dryer started. It did. The end. Also I was told it would be a couple days till I received the ordered part. It was here in less than 24 hrs. Thank you for your excellent help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Ringgold, GA
- Parts Used:
- 5303281153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Really Loud Squeeking Sound
I watched the videos on this excellent website first. Then the repair was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANDRENNA from MAPLE HILL, NC
- Parts Used:
- 5366021400
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Dryer door wouldn't remain closed.
Once I received the product I placed it in the hole and it worked great.
Was this instruction helpful to you?
Thank you for voting!