GLEQ642CAS0 Frigidaire Dryer - Instructions

Removed 2 rear philips sheetmetal screws. Popped lid off w/ flathead screwdriver. Rotated old switch counterclockwise. Moved 2 terminals from old switch to new. Put everything back together in reverse order.

i removed two screws that hold the top of the dryer on at the back of the dryer then i removed a couple of screws that hold the front of the dryer on at the top of the front then i disconnected the two wiring connecters inside the front and a ground wire when the belt came i put it around the drum and took two screws out on the back of the dryer near the floor that hold a small panel in place to access the motor i put the belt on the motor and idler wheel and that was it put together and done

I watched the video that I saw posted on youtube. My dryer did not have a panel on the back to remove, so the part was very easily accessible. I simply took the old switch off and replaced it with the new one. The most impressive part was receiving the part so quickly. That was awesome! It saved me a trip to the laundromat. I really did not expect to receive it so quickly. Thank you!!!

removed the old gasket with pliers (noting where the beginning/end of the gasket was) then installed new gasket in the exact location with very light pressure on each rubber insert point. Voila!!

Appearances can be deceiving.....while dis-assembly was a piece of cake; the problem turned out to be failed welds on the dryer drum. REMEMBER this before you make a parts decision. Examine the problem.FIRST! (this comeing from a guy who used to Manage an appliance repair shop WAY back in the day....DUH!)Solution?....new dryer; repair cost too high. None the less...at least I have a spare belt !!!

I removed all but one screw on the back of the control panel and slid the panel down and to the left. Then I jiggled and turned the start switch box out of the slot, unplugged it, plugged in the new switch, and put it back in the slot turning slightly to tighten into place. I replaced the screws and the repair was complete!

Removed drum and replaced drum support bearing.

Taking apart cleaning putting back together I don't have any h-t lube so ill be doing it again. Thanks for the part ill be calling again!

My Son-in law did the repair. He removed the top, the front lower panel and finally the front panel with the door. It took a little more time than anticipated because there was not any explicit directions on how much to remove to replace the belt, but he got the job done and put it back together very quickly. Glad I have him to help when needed:).

I used the posts on the site to ascertain the problem (fuze or element burnt out). The pictures were very helpful. I pulled the dryer to the floor and using my meter checked both the fuze and the element. The electrical diagrams were very helpful also. I took the dryer apart further to make sure the coil was indeed the problem. I then ordered the part!

Got the belt for my little bro's dryer . . . he and a friend tore into it without looking on how to do the job . 2 hours later dryer apart not fixed . . . LoL . . . Next day I get a Call asking me to find a repair manuel . . . I laught and told him to go to Youtube on his phone and the video would tell him how to do it ! He is back up and drying . . . Moral to this story . . . look before you leep !

Removed obvious screws to the vent etc. Then had a little trouble getting the cabinet open. My only problem was getting the front top panel off. A clip about 2" from either side at the top needs to be pushed in with a flat head screwdriver to release the top. Other than that the task was pretty straight forward. Two sets of wires to the heater itself. Used pliers to help pull them loose.

The dryer was heating but the drum would not turn. We opened it up to see what the problem was. As soon as we opened it, we saw the belt was broken. I ordered a new one and after two trips to the laundromat I was ready to get the dryer fixed. That weekend we tackled the job. First I did a Google Search on Westinghouse dryer repair, found several ....one with a video:-) Punched in our model number and they went through the whole procedure....while it took them only 10 minutes, we took a little longer. But they had great ideas how to hold the drum while repairing, etc. Being recently laid-off this was a fantastic find. I have no idea how much a service call would be on the dryer nor could I afford a new one at this time.... Great old American Know How got it done.

Simply pulled the old knobs off & put the new ones on.

It is disappointing that the knobs cracked at all. I guess all the repair guys who've come out since our kitchen remodel are right - nothing lasts anymore & expect a repair within 5 yrs.

I ordered on a Monday & the knobs were delivered the next day, even though I chose only standard shipping. I was very, very pleased with PartSelect.com.

Very easy, slipped the old one off and placed the new one on

This was the greatest part ordering experience I think I have ever encountered.

No problems with ordering, arrived on time and works beautifully.