FGR211CAS1 Frigidaire Dryer - Instructions

I simply had to open the plastic and stick the new timer knob on the dryer. It fit perfectly and more importantly, it arrived within 48 hours of me placing my order. Thanks!

When the Time Knob broke, I planed to buy a new dryer. My friend told me of this site. I cheched the site and made the order, less than 36 hours, I received the part, less than 1 minute. I replace the knob and it bakc to work. It costs me only $15.

How I love this site!

Repair was simple and easy. I thought I was going to have to get a new machine.

Thanks

First, I took the new knob out. I slipped it easy on the washing machine.

It was all done.

pulled old one off lined up new knob pushed on new one no tools-- less than a minute..

Just a matter of taking off the broken knob and replacing it with the new one.

I replaced this belt once before but it squeaked for over a year. This belt from Part Select was much better quality and now the dryer works perfectly, no squealing!

Found part through Google, ordered part and received it in three days. Easy as pie

There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.

Two weekends ago, I was doing the laundry and when I went to turn the knob on the dryer, the inside part broken. I had to use a pair of plyers to turn the timer and finish drying the rest of my clothes. I had ordered from Parts Select three years ago and I went to their website which had been updated and found the part I needed. They even had instructional videos to describe which was really neat and it was very easy to order a replacement part. Because of the low price on the dryer timer knob, I ordered three just in case in the coming years the timer knob breaks again. Thanks, fm

My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.

After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!

Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.

I decided to replace the cycling thermostat. I disconnected power, used the putty knife to push back spring type retainers underneath the top and
lifted up the front edge of the top and pushed it upward to rest on the back hinges.
Next, I unscrewed two sheetmetal screws on the edges of the front panel.
Then I supported the front panel upward while releasing the push type spring clamps before pulling it forward off the drum. I was able to swing
the front panel open from the left side and gently open it while watching one wire that was connected to it from the right side.
Then I was able to take the terminals off the thermostat noting which way they were connected.
I unscrewed the two screws holding the thermostat to the fan housing and replaced it with a new one. I assembeled from the front panel bacwards. until the top was back down.
Upon testing the unit I found out that the problem was not the cycling thermostat.
I plan to investigate the timer circuit that the thermostat controls next.
One can take out the thermostat and test it for cycling by removing it and checking terminals with ohmmeter x1 range and heating and cooling it with a hairdryer. Meter will read zero when thermostat is cold and closed. It will read infinity
or high resistance when it is open and hot.

I pushed the knob onto the metal dryer piece. It was repaired in less than 10 seconds. Also I was very impressed by the fact that I ordered the part on Thurday morning and I had the part the very next day. I am a happy customer and will recommend parts select.com to others

doo handle snapped in place an replced screws that were missing