FGQ221CAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Natalie from Jasper, TN
- Parts Used:
- 134503600
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Loud Noise in dryer
Removed the top and front of dryer. Removed the old bearing and held the new bearing in place while my husband tightened the bearing into place......easy......now the dryer runs quiet again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from New Iberia, LA
- Parts Used:
- 134398300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Unhooked wires turned switch to the left put new switch in and turned it to the right 1/4 turn and put knob on front of switch this is the best parts web I have been on so far.
Was this instruction helpful to you?
Thank you for voting!
door handle an screws missing
doo handle snapped in place an replced screws that were missing
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellen from Baltimore, MD
- Parts Used:
- 131450300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
lint filter bent
Vacuumed lint and inserted new filter.
Was this instruction helpful to you?
Thank you for voting!
they where just wore out.
Taking off front of and top of dryer and panels on the back. Releasing the belt and taking out the tube un screwing the two pieces off the back of the machine putting new ones in and putting belt back around drum and setting drum in. Then holding drum while the front is put back on then attach top and a couple panels on the back.
Was this instruction helpful to you?
Thank you for voting!
Dryer drive belt broke
I opened top section with a screwdriver, pushing in the release.
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
I opened front panel with door with screwdriver pushing in the release.
I lifted drum out through the front.
I replace the Idler Arm assembly.
I greased the rear drum bearing race.
I vacuumed out and cleaned blower and dryer area.
I put the new belt on the drum, reinstalled the drum.
I put belt around drive motor and Idler arm assembley.
I put front panel with door back on.
I put the top panel back down and snapped into place.
Tested dryer, job done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sean from Sacramento, CA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Due to weather exposure, the handle fatigued and broke in several parts.
You simply pry the old handle off with a flathead screwdriver, and then line up the new handle and snap it into place. It took less than 30 seconds! A breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- August from Las Cruces, NM
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Start knob broke
Pulled the old knob off to get part number. Ordered replacement part. When it arrived, I pushed the new knob on the shaft. It ain't rocket science! Thanks for you quick, efficient service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from San Diego, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knob was broken
Not much needed to replace a broken knob. I was very impressed with the fast service and will recommend Partselect to my friends.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- LINDA from LONGWOOD, FL
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
need knob
buy need knob
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shannon from San Juan Capistrano, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Broken rotary knob
Easy peasy! It is as easy as lining up the knob with the D shaft on the dryer. There is a small piece/ring around the shaft that can still be stuck up inside so if you can't get the knob to sit flush with the dryer, peak inside and slide it off with a pair of pliers (the repair video shows this clearly if you need an example). I was done in 2 minutes, including the time it took to open the package!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Renton, WA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The knob broke
I unplugged the 110 on the dryer, then popped the top on the dryer (with a screw driver), held the switch in place, bent the brass fittings to clamp the switch assembly to the front of the dryer panel and installed the knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rachel from Memphis, TN
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Dryer Starter Knob
I pulled off the broken knob and black fitter that was originally on the plastic piece. I didn't even need pliers. Then I replaced the new rotary knob under 5 seconds. Now the dryer works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Margaret from Gainesville, VA
- Parts Used:
- 131644700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door handle broke off
I replaced it...just popped it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darla from Alvin, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
brocken knobs
Very simple just put the new ones on to replace the old knobs that broke. Thanks for the quickness of getting our parts to us. So nice to not have to use a tool to turn the dryer on. Very happy with the pricing and quickness it was delivered to us.
Was this instruction helpful to you?
Thank you for voting!