FGQ221CAS1 Frigidaire Dryer - Instructions

I popped the dryer lid open by pressing on two latches with the flat putty knife. I found that I really needed another set of hands, so my son helped me with this project. I had to disassemble the front panel by unscrewing 2 screws on the sides and also 2 screws around the dryer timer knob, after removing all knobs. Also, I had to pry apart 2 of the front pieces because they are clipped together with plastic latches. I unhooked two wires from the starter switch and then gave a half twist to remove it from the opening. Once that was removed, I just replaced it with the new part and put everything back together in reverse order. I did test the dryer before putting back together, but make sure you unplug it again while assembling. I forgot and two wires touched and there was a big spark and popping noise. Fortunately, nothing was blown out and no one was shocked I had absolutely no experience with anything like this but found this website to be a huge help. I figured everything out just be looking at the diagrams and some other notes on-line. Thanks!

I watched the video on the web site after selecting the part and it was pretty simple. Everything worked just like the video showed. Probably could have been done faster but I took time to vacuum the inside of the dryer out. Really liked the video.

I love technology. First thing I did was google on "U-tube", "How to repair a squeaking dryer". Several videos out there so I just found the one I needed and watched. The repair itself went easy. A word of advice would be to be careful of sharp edges and to remember to unplug the machine prior to repair. While the drum is out, go ahead and get your shop vac and clean the inside of the unit out. Also, not only put grease on the new plastic holder, but put some on the shaft of the idler puller. I also used an awl to line up the holes on the front panel when re-installing the screws. One video I watched showed reaching in through the front to take the drum belt off the pulley, where another showed removing the inspection plate on the back. This made it much easier.

The dryer was heating but the drum would not turn. We opened it up to see what the problem was. As soon as we opened it, we saw the belt was broken. I ordered a new one and after two trips to the laundromat I was ready to get the dryer fixed. That weekend we tackled the job. First I did a Google Search on Westinghouse dryer repair, found several ....one with a video:-) Punched in our model number and they went through the whole procedure....while it took them only 10 minutes, we took a little longer. But they had great ideas how to hold the drum while repairing, etc. Being recently laid-off this was a fantastic find. I have no idea how much a service call would be on the dryer nor could I afford a new one at this time.... Great old American Know How got it done.

Dismantled the dryer to determine that the belt was broken. Called a local supply outlet to request a belt. They said they couldn't find one. Did an online search and found Part Select. Called with the model number and within three days the part was delivered. Replaced the belt and the dryer was working within an hour. Hardest part was getting the dryer out of the laundry room. I would certainly call PartSelect again if I needed a part.

Removed access plate in rear, raised top panel, removed two screws holding front panel (with door) put new belt over drum. Threaded belt through path between motor drive and idler wheel. Put everything back together.

My order was shipped very promptly, and was received very quickly. It is wonderful to have this service available on the internet. I can remember how difficult it used to be chasing down parts before. This was impossible in smaller cities.

Removed top and front of dryer and rear panel. Installed belt and new idler pulley. Reinstalled top and front panel and rear panel. Dryer worked great.

Popped the top... disconnected wiring... dropped the front... replaced coils... reversed sequence... done deal. No hassle, no worries, easy as 1-2-3!

Removed the top of the dryer above the dryer door by pulling the pop out plastic holds. I then removed the dryer plug in at the top inside dryer that controls the start when dryer door is closed. I thenremoved the screws that are located at the back of the dryer tub where the bearing is located. I then replaced the support bearing. I just replaced every thing I took off in reverse.

Very easy fix on this system as described in other reviews. Simply unplug, lift top, remove two retaining screws on the dryer face, remove face from front of drum. Locate both coils at the lower left corner of the gas valve assembly.

Unplugged the electricity, turned off the gas, then pop open the top of the dryer. Removed the two screws and pulled the front of the dryer off. Removed the two screws that locked down the two m series ignition coils. Put it back together and all things worked great.

parts arrive just like they said they would .had parts installed with in 15 minutes was drying clothes thank you your advice was perfect.

the parts you supplyed were exact replacement and were very easy to replace, your fast shipment made my wife very happy, thanks.
poppop in florida

I recieved the knob the next day after I ordred it. I just lined it up and snapped it on and I was good to go.

just unplugged the old one, plugged in the new made sure it worked and put it back together.