FGQ221CAS1 Frigidaire Dryer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Fred from Coronado, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob on Dryer
Pulled broken knob off and pushed the new knob on. It was about as easy as it gets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- frank from bayside, NY
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
on/off knob replacement
Piece of cake to remove old knob and replace with the new. Really impressed with delivery of the part the next day. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TIM from CHINO HILLS, CA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replace knob
took off old knob and put on new knob used my hands
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Hudson, NC
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer ran but no heat.
Followed instructions and the repair went very smooth from start to finish. From getting tools out of tool tray to putting them back it took 15 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARYAN from LOCKPORT, IL
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The start knob cracked and I had to start the dryer with pliers
I recieved the knob the next day after I ordred it. I just lined it up and snapped it on and I was good to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Celia from El Paso, IL
- Parts Used:
- 5303931775
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Dryer was tumbling, but not heating or drying clothes
There was a small plate and 2 screws holding the 2 coils. I just removed the screws, unplugged the 2 coils, plugged the new ones in and put the dryer back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from charlotte, NC
- Parts Used:
- 134503600
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
broken belt
I replaced this belt once before but it squeaked for over a year. This belt from Part Select was much better quality and now the dryer works perfectly, no squealing!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eliot from Dedham, MA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old Knob Broke Off.
Opened the package. Took out the new knob. Popped it on the old metal prong. Don't have to use the old pliers to start the dryer anymore. One of the little things around the house that was broken, just took a minute to order, a day or so to receive, a second to install and it was one more thing off my to do list. That was about the quickest and cheapest repair we made at our house this year.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from Cape Coral, FL
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
old plastic knobs broke
the parts you supplyed were exact replacement and were very easy to replace, your fast shipment made my wife very happy, thanks.
poppop in florida
poppop in florida
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melanie from Nacogdoches, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Rotary knob broken/unable to turn on unit&end of cycle buzzer
Both rotary knobs broken and already removed. Just put knob back on spindle lining it up properly when putting on. Took less than 3 minutes--Yes!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Potosi, WI
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
control knob broke to starrt the dryer
simply pushed it onto the control
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamera from Fair Oaks Ranch, TX
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
rotary knob broke
Just slipped it on --- easy as that!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kirby from Sandusky, OH
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
coils would glow but not light !
After reading other peoples problems i decided it must be the coils after looking at the picture of the part I looked at the dryer to find were the part was. it was right in front behind the inspection cover. so i order the part. it came very fast.these are not the first parts i have purchased from Partselect.the web site is newer now and i am glad because reading other peoples problems help me decide what was wrong with mine.PS Always clean every thing inside the dryer!! 15-20 min job one screw driver! (19 year old unit works fine)thanks to Partselect!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- barbara from Saugus, MA
- Parts Used:
- 131965300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
cracked knob
I pushed the new knob onto the post.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Case from Los Angeles, CA
- Parts Used:
- 5303931775
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Dryer not heating up consistently
My dryer was heating up very briefly blowing hot air initially then cool. I have a stacking washer/dryer set (2002). I initially turned off the gas valve at the wall, ran the dry for several minutes to clear the gas line, then unplugged the power. I was then able to pop the top using a flathead screw driver, securely prop it open, unhook the wiring harness to the front panel, unscrew the two front panel screws, and remove the entire front without having to unstack the units. From there, you remove the two screws holding the bracket over the coils (2 of them), remove the electrical connectors attached to both coils and replaced them with the new ones. I then replaced all brackets, screws, and such (you'll need to lift the drum when putting the front back on and make sure it is lined up), plugged it back into power and turned on the gas to test the unit which worked perfectly. The 62% of the time seems to be an accurate figure as nothing else had to be done to the unit. Pretty easy stuff...good luck.
Was this instruction helpful to you?
Thank you for voting!