UAN8305-80A Frigidaire Dryer - Instructions

There was a lot of screws. And I cleaned everything well. The one part was bad so I replaced them all to make sure it'll last.

I first removed a vent cover in the back where the idler is located. With pliers I removed the tension off the spring. Next I simply slide the idler off the post. I pulled up on the top panel which opened like a clam shell. I used a flat blade screw driver to separate the front panel from the dryer so I could slide the new belt around the drum. I reversed the steps. All in all it was easy. It took me about 30min including cleanup.

I raised up the top then took 4 bolts out of the front and it came off and then I slipped the belt on. Now was the fun part. I tried to put belt around the tension spring from the front of the machine. Bad mistake. So I turned the machine around and took off little plate bottom left, back side reached in and WA-LA back in commision. I took a long brush and cleaned all I could reach and put it back together. Bingo, back in business.
And I'm 71 yrs. old.

I am a "do-it-yourselfer" despite my husbands opposition. I followed instructions from one of the posts on the site and took apart the dryer. I found the location of the rear bearing and took it out and replaced it with the new one. Easy as that. Made sure the parts looked the same. Made sure I saw how everything went together. I used a magnet to hold the ball bearing in place on the rear mount and taped the metal bracket on the outside of the dryer. Screwed it right in. Reassembled in reverse and works like a charm. To all the women out there who don't think they can do this. It's easy. Give it a try.

After changing the drum support bearing, and the front felt ring, the noise continued. It turned out to be the tensioner pully. The harmonic vibration travels throughout the dryer box like an instrument so you can't tell where the sound is comming from. Before you do anything, spray a little wd40 between the bushing and the shaft on the belt tenioner pully. If the squeel goes away, you have found your smoking gun.

Watched Video Provided. Very Simple Repair. Asked my lovely wife to hold drum in place while replacing drive belt. She gladly complied and is back doing what she seems to love most. And no, I'm not kidding. Our washer and dryer seem to run 24/7/365. I've completed various repairs on both appliances over the last couple of years and saved 100's of dollars thanks to this site .

First of all, I've purchased a belt from local service center that cost me more than $21 (local tax is 8.5%). But, I can not find the idel pulley assembly so I searched on the Internet and ordered from PartSelect.com.

Surprisedly, my order came just one day - they must cross-ship from local distribution that it's even faster than to get those in local stores (driving .. and hope they have what I want ..).

I've replaced the belt 2 days ago - it's easy with 4 screws removed to pull out the front door. The back panel is opened with 2 screws remove, and very easy to replace the pulley.

It's a heavy duty gas dryer made in 1989 and this is the third time I changed the belt and the first time to change a new pulley. I would recommend to change the idle pulley because I may not need to change the belt if I have had replaced it last time. A broken or not functional idle pulley may damage the belt in a short time.

Appliance such as gas dryer like mine will last forever with replaceable belt and pulley. I'm really happy to see a working dryer (almost 20 years old) and my wife is asking a small component for her washer .. that I think I can easily fix that too .. with the help of PartSelect search.

Hope this will help.

John

Open the back plate. Broken pulley was already out of place. Put the spring on the pulley and placed it. It took me less than 10 min

Super simple pushed in the new receiver and boom all good and working

The first thing I did was logged onto the internet to search the web for my dryer information. Next, after I found the correct model, the site referred me to the parts section and that is where I determined the problem was the M series ignition coil. I then unplugged the dryer and turned off the gas. I took a screwdriver and popped the top off and cut the wire straps that held the door strips and the light to the front panel. I then unplugged the door switch at the connector - HOWEVER - DO NOT TRY TO REMOVE THE WIRES FROM THE ACTUAL DOOR SWITCH BECAUSE THEY ARE VERY FRAGILE AND CAN EASILY BREAK. Next, I removed the two screws that hold the front panel on. By using a slight bit of pressure, I removed the front panel and was able to locate where the ignition coil switch was. (It was right in front) I then removed the two screws that held the clamp down, as well as the bad coils. The coils easily slid off the post and the new pieces slid back on just as easy. I then replaced the screws and clamps to hold the new pieces in place and replaced the front panel. **NOTE ~ while the front panel is off, it would be a good time to clean out all the built up dirt and lint that has accumulated over the years. Lastly, I re-connected all switches and wires and replaced the top panel. Once I turned the gas back on, everything ran beautifully.

First removed the top of the dryer, then the front of the dryer. Took the plate off the back left of the dryer to disengage the belt off the pulley.
Took the three screws out that hold the drum in place, of course the third screw stripped and had to use a screw remover, which didn't work, but the adjustable pliers did so then lifted the drum out of the plastic reservoir in which the bearing laid. Next unscrewed the two bolts holding the plastic reservoir which also loosened the small metal piece on the back of the dryer where a small bearing is located. Put the new parts in, but instead of putting the larger bearing that fits in the plastic reservoir, I decided to put it on the drum first and guide it into the reservoir all at once, this worked well . Prior to that I put the new plastic piece on the inside and taped it there while holding that piece put the small metal piece with the small bearing on the back of the dryer. I'm sure it is alot easier with two people doing this part, but it worked and I didn't lose the small bearing. Next put the front of the dryer back on and then put the belt back on the pulley, then the top.
It definitely helped immensely to read how someone did this, just follow the instructions given and there you go, no more annoying squeak and also a feeling of accomplishment and thanks to the person who wrote the story on how to do this job, appreciate it.

lacked instructions. Internet yielded a simple paragraph. Scored real bonus when we discovered the lint build up past the internal filter was approaching catastropic level. Replaced the exhaust tube (plastic) with rigid metal and resolved to disassemble and clean dryer on 2 year cycle in future. Kit just isn't complete without detailed instructions. Parts were complete and sufficient. Local codes have eliminated the plactic exhaust tube. Recommend that all old installs refit to rigid or semirigid before the fire happens!

I lifted the top at the front edge, slid the top back, disconnected the ground wire connected to the top at the rear edge, just slides off.
Then removed the phillips screws on the inside front edge, only one on each side,near top of dryer disconnect the wiring harness at the right side, cut the nylon tie strap holding harness also.
Tip front panel out a little and lift up, comes right off.
The coils are in plain site on the gas valve, remove the wires, and the two screws holding the bracket that holdes them in place, slide the old ones off and start putting back together.
I also used a vacume and cleaned all the lint and dust off everything I could, including the air intake at the rear of machine, "Peice of Cake"

Opened the top, removed the 4 screws that held the front top the cabinet, took the front off, went after the dust with the vacuum cleaner, lifted the drum, installed the belt, put the front back on, and put the belt over the idler. Most of the time was in the cleaning.

As all others have said, without being redundant, I'd view post #1 or #2 for a good detailed set of instructions.

The primary issue I had was with the stainless steel ball bearing that was shipped with the kit. I couldn't figure out what it was used for, because when I removed the bearing carrier the ball fell out before I could see where the original one was located. The stainless ball bearing is a grounding ball, not a bearing. It goes on the exterior of the plastic bearing carrier/receiver.

Once I figured that part out, it was a piece of cake.

Took a little longer than other people's repairs, but I also put a new belt on and re-worked the exhaust duct for solid ducting versus flexible duct. fine-tuning the rigid duct work was a piece of cake with the tumbler out, since i could crawl right inside the chassis and make sure everything would line up (level legs, adjust elbows, etc)