CDG4205AWW Crosley Dryer - Instructions

Just took the old one out and put the new one in! Fit perfectly! Very happy with your service and part came super quick!

Per instructions I printed off online: took off door, then the front panel. Pulled out the old switch/button, connected the new switch/button, made sure the new button was working; put the panel back on then the door and DONE!

The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.

A new gas valve solved the problem. The valve was an exact match but the gas fitting nut has a slightly larger diameter and required a minor modification to the 30 year old Maytag mounting bracket to provide clearance.

Replaced the motor with a new one from partselect per the YouTube video. Had a problem with delivery of the motor. I paid for next day delivery. FedEx picked it up and it made it to the first stop, Indianapolis ok and then stopped. After a week went by I ordered a second one. That one came as promised + 1 day so I’m satisfied. The telephone people were very well spoken and attentive to my discomfort and again I’m satisfied. The motor was at least 25% cheaper than if I bought it from Maytag so the savings is significant, about $50.

Found the high temp thermostat was shutting off the gas after just a few seconds. Tested the thermostat and it looked like it was opening at 180 degrees as opposed to the rated 240 degrees, so I ordered one from PartSelect, which shipped the next business day. Replaced the thermostat and no luck, still shutting down after a few seconds. Turns out the duct going outside the house was blocked with years of lint stopping the air flow. Cleaned out the duct and the dryer is working fine again. Wife is happy she won't have to go to the laundromat.

Removed Dryer Door and front face of dryer, total of 4 screws, turn dryer drum to position broken baffle screws, remove screws, install new baffle, attach front face of dryer and reattach dryer door. Time 15-30 min. total. Real easy. Thank You PartSelect. Maytag told me my part was no longer available, but I fold it at PartSelect.com.

Take old out, slide new one in. Perfect fit.

take screws out of front of dryer, pull front off to expose drum and replace baffle

unplug dryer; remove dryer door; remove front cover; thermal fuse located on heater underneath and beside drum; remove two electrical leads on fuse; remove two screws holding fuse in place; install new fuse and do the above in reverse; clean lint from duct; plug dryer into

Followed instruction video

Removed four screws from the door hinges and front panel. Removed the front panel by pulling forward from the top and found two screws. The part does not come with screws which are #10 x 1 and 1/4" long hex head sheet metal screws. I believe that the screw size is critical as the part may break loose again if the screws width is too large or small for the predrilled holes in the baffle. One set of holes in the drum had slotted screw holes which would allow for installing the baffle with the screws partially installed in the baffle. I would recommend washers for that installation. Check all three baffles to ensure that all screws are tight.

I followed the Part Select tutorial on Instant Repairman and retrieved the missing screws at the base of the dryer as described in the tutorial and after trying to reassemble the original baffle notice the baffle screw holes were stripped. I decided to fill the holes with a strong glue before reinserting the screw to temporarily keep the machine running until the new baffle arrived as it was just ordered the night before. When the new baffle arrived I decided to hold onto it as a spare if or when the original baffle broke off again.

There are several parts that will cause the dryer to squeak, drum roller, idler pully and the drum slides. To start, remove the door and the two opposite screws. Pull the front cover down and remove, no screws to remove, this is a snaped on piece. Next, remove the two screws holding the dryer top bracket and lift the top. Take drum support by removing the screws and then remove the belt from the motor and remove the drum. The hardest part was removing the C clips from the roller axle even with the snap ring pliers. Replace the drum rollers and reverse the process to re-assemble. Of course, the rollers weren't the problem even though they were worn out from 20 years of service. I ended up replacing the idler pully and and the idler pully support arm. If I had all of the parts prior to starting, the total time would have been about an hour. I did watch several YouTube videos before attempting the repair. That helped me understand the "how" and made it easy once I started the repair.

Really easy to replace. All I had to do was remove the screws on the hinges and two on the other side. Used a nut driver to remove the brackets that hold the lid down. Secured the lid open and used the nut driver to remove the screws that hold the baffel son (two on each) and replace the baffel and secure with the screws. Reversed the the process and was drying clothes my first load of clothes in around 30 to 40 minutes. Process is really easy and I was able to do it by myself