DV316BEW Amana Dryer - Instructions

IMPORTANT!!! Unplug the unit first!! 1 - Remove two screws on the back of the top of the unit. Pull back a little on the top to release it from underneath the control unit on the front of the dryer (the piece with the dial and buttons). 2 - Remove the four screws from the control unit. They are located at the top of the dryer. Pop off the control unit - don't worry about breaking any wires as there are none. 3 - Remove the front of the dryer by removing the four screws that are NOT used for the door and door latch. I had also removed the door latch and door but I don't think it is necessary to remove them. The front will swing out from the bottom where you can unhook it and remove it. 4 - the heating element is located on the front of the unit, bottom right. Either draw a diagram of the wires or take a picture of them with your cell phone. Smart phones are great for this as you can zoom the picture if necessary. Remove the wires (they just push on but it may take some effort to get them off). It's either one or two of the wires that are not part of the wiring harness and they go from one part of the element to another so don't get excited if these wires fall down - you haven't done anything wrong, they are just loose. The one screw in the front holds the element in (the back of the unit just rests in that hole). Remove the screw and pull the unit out. Put the new element in, hook up the wires before positioning the element. Put the screw back in that holds the element and put the rest of the dryer back in the reverse order.

I had a problem a couple of months ago with the dryer not heating and replaced the thermal fuse after checking the the parts with a voltage meter and the dryer worked fine. When I did the repair I also cleaned all the lint out of the dryer, exhaust, and the vent. It worked fine. A couple of weeks ago my wife commented about how hot the dryer was and it seemed unusual. I realized there was another problem but before I could check it, the dryer stopped heating again. Some time ago, the sensor dry funciton quit working so I just went ahead and changed all the electronic componets, the two on the exhaust tube and the two on the heating tube. I assumed the high limit thermostat failed. After unplugging the dryer, I took the two screws loose on the top backside of the dryer that hold the top in place and removed the top, sliding it back. I removed the four screws holding the control panel in place and rotated the panel forward, then up and out of the way. I removed the four screws along the top of the front panel, then the ones from around the opening on the front, and the front door. There was one screw that held the heating tube. I removed it and the tube slid forward. I took the front wire lose and rotated the tube clockwise to pull it out and took off the back wire and changed out the thermal fuse and thermostat. The exhaust tube was right there in the front and all I had to do was change out the parts on it. Everything went back to gether as easy as it came apart and when I plugged the dryer back in, it worked just like new.

This was a simple repair. Removed the small access panel where the vent pipe comes through, the roller is right there. Unscrewed the support roller bolt, looking for all the pieces that had broken and fallen inside the housing of the dryer. Using the washers and nut from the old one, put the new roller in place, be aware that you have to lift the drum a little bit to get this new roller in. It could take two people depending on your strength. Tightened down the roller, spin the drum by hand to make sure it was ok, then put the access panel back on and fired it up for a test run.

You know! I forgot exactly where it was i got the info to fix the problem but, "Parts select" was mentioned. Once I had an idea as to what to do I then, wasted time around town looking for the parts with no results. I then did what I should have at first an ordered the parts from Parts select. got them in the mail, lightning quick! I think I may have found the info here as well,not sure. (this site is awesome None the less) but the info led me to the Thermostat, I then jumped it as indicated and wham!! it ran. Order both the thermostat and thermistor. only problem I ran into was, removing the front display panel. broke some of the retaining clips off in the process. all in all, it was an easy fix that saved me a bunch of dough. greatfull to parts select for a speedy deliverie and to the website that made it possible. think it may have been here at the free repair help, section. awesome and highly recommended thanks!!!

changed high limit switch, and sensor grid and thermo fuse

I was working on my daughter’s Maytag dryer model MDE 9700 AYW. The dryer had been making a bumping sound for some time. It had the same symptoms a few years back, but it was still under warranty. The repairman had to replace a drum roller. He told her at the time he should replace all of them but he only had one with him. So when my daughter heard a similar sound she assumed it was a drum roller again so I ordered the roller without taking the dryer part. She has four boys that generate a lot of laundry, so she needs her dryer daily. I wasn’t sure how long it would take to get the part or do the repairs. The roller arrived very quickly, I think in a couple of days. The drum rollers on the dryer did not need to be replaced. What I found was bumping the side to the dryer because the sheet metal had popped inward. The drum has very little clearance on either side. The side probably could’ve used another crease or something to make it more rigid. My time wasn’t, wasted. I think it was will spent. I found that 3+ years of lint at piled up significantly on everything. The lint on the shroud for the heating coil had already turned brown and could have caused a fire. I would suggest to anyone who’s had a dryer for a while should open it up and vacuum out the lint buildup.
It only takes a Phillips screwdriver and very little time. It’s a very little investment for your peace of mind.