DV316BEW Amana Dryer - Instructions

Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove front door ( 4 screws on top 2 on bottom) Changed the thermostat and thermistor. Saved 320 dollars :)

Remove dryer covers and locate heater assembly. Removed heater assembly and checked visually if the heater coil is opened, I verified this with an ohm meter. Heater Continuity was OK. Next step I checked the heater sensors. Thermal fuse with bracket had no ohm meter reading between two terminals[open circuit]. Order part#35001193 "thermal fuse" with bracket from "partsSelect.com." Assemble back in reverse order. Please note that the dryer heater was filled with lint and needed a good cleaning.

top and the front had to be removed to get to the fan... the thermistor that sits in the exaust fan went bad... the heat would come on for a few minutes then turn off completely not getting to clothes dry.....

YouTube, YouTube, YouTube. I YouTubed many videos on how to take a dryer apart to reach the drum support roller and axle. After watching numerous videos, I settled on one that had my exact model of dryer. For my dryer, previous inputs said I needed two rollers to for my model. That is not the case. My model actually has 4 rollers, 2 in the front and two in the back. I ordered 2 initially but only needed 1 thankfully since only one roller was bad. Keep it simple stupid is how I got it done. Dryer's are pretty simple machines mechanically. Don't trash your noisy dryer. We bought ours in 2014 and it only recently started giving us issues. This is after 2 moves and being run daily for a family of 6. I'm glad I found partselect.com. They saved me a ton of money.

Had to pull the top off and the front of dryer with a few phillips screws and was able to get to the thermistor and I also replaced the heating coil because it was bad.The cause of the problem was because of a clogged up vent. It was a easy replacement.

had to take top off to get to the front cover screws.Then took the screws out of front cover, pulled it off then pulled the drum out. Man at the amount of lent in the buttom and in the heating element area. Well, after removing drum I found the problem with the pulley. When I got parts to put back together it took a little time and thinking to find out how the pulley an belt went together(belt came off when pulley finally melted in half)with holding drum up to see what's going on. The pulley is laying down,with drum in and belt around it put belt on motor shaft then pull pulley up vertical wrap belt coming down on motor side around pulley. Then put it all together.

Samsung had no servicers available, after over 3 months calling and sending photos and signing papers they sent a refund. Never any advice on repair from Samssung. Saw a video by JEFF OSTIROFF that lfor disassembly and location of heating parts. Gor $40 Samsug service manual that was rather useless. Disassembled and tested thermostat, Thermistor, and heat element. Appeared that HI-HEAT thermistor was open circuit all others OK. Sent for new one, arrived damaged insufficientlyb packed Tested original again out of appliance, tested OK. Got replacement for damaged thermistor and put it in, reassembled and IT WORKED! Notvsure if original thermistor was intermittant, or connection problem was the fault.

Dryer would not start but electronics were working.

Pulled top of dryer off; noticed the belt was loose but not broken.
Went in through the back (1 screw and removed the exhaust pipe/plate); noticed the wheel was broken and thus the belt had fallen off.

Ordered replacement wheel/arm.
One screw to remove old one, one screw to install new one...tentioned the belt. Dryer was good as new.

A month prior to this repair, I took the dryer apart, cleaned the clogged lint out, and replaced the thermistor with a cheap aftermarket part. It lasted a month. Bought this more expensive OEM thermistor, hopefully of a better quality. Realized that I could have gotten to the thermistor from the back by simply removing the vent pipe and carefully reaching through the vent pipe hole to take out the thermistor. Did that this time instead of taking everything apart. Also bought an updated lint screen (aftermarket part). It has better mesh although it doesn't fit quite as perfectly as the original. So we'll see if the OEM thermistor lasts longer. The repair time was mostly spent moving the washer and dryer within a fairly small laundry room. The air lifter really helps.

To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.

First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!

I originally called a repair person to come out but that was a total waste of time and money. He removed the front of the dryer claimed there was a dryer sheet causing the problem and put it back together.
Never again!
I watched a youtube video for step by step instructions on how to take the dryer apart.
I took the front door of the dryer off, removed the filter cover and the dryer drum & belt. Removing this was simple and allowed me to see everything I was working on. With the new part in hand, I removed one wire at a time from the non working heat sensor and connected it to the new part. That way I was sure I had the right connections.
I then removed the thermostat making sure to put the new one back in place exactly as the old one.
I then put the drum back in place with the belt securely fastened. I put the cover back on the lint filter and placed the dryer door back on securing it in place. The dryer is now working perfectly. It takes longer to take the dryer apart than to replace the old parts.

Self with you tube
app thanks.

This repair is easy. The only drag to this repair is you need to almost completely dismantle the dryer just to get to it. So keep track of your screws.........Look on you tube for videos to dismantle the dryer, you will need to take this down to the drum to change....Once I replaced the pulley, it was about 30 minutes later the dryer was operational again.

Disassembled and tested each part with a multi-meter. Found that the thermostat and fuse were bad. Replaced parts and it is working again.