MDB8601AWS41 Maytag Dishwasher - Instructions

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

It is such an easy snap-on repair that a child could do it. I am grateful that your company had a picture so I could compare my broken part with the ones you guys have as I couldn't find my model number. I took my time to do the job right, so it took me almost 15 seconds! lol

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

with dishwasher running I would open the door and notice the lower spray arm was not turning. I removed all parts in the tub and clean off all the accumulated gunk (likely combination of food and soap scum - like a white paste) . The accumulator screens where more than 50% clogged with no way to clean the inside. I replaced the accumulator part and the lower spray arm because 2 holes had gunk in them that would not come out. dishes are now getting clean and I am switching to liquid - no more powder as I suspect it caused the build up over time.

I followed the you tube video exactly. Very easy to do. I did not tighten the screws sequentially as shown in the video, rather I did the opposite ones to make sure nothing was skewed. Very easy, about 20 minutes.

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

The control panel is pretty simple to replace. Take the inside of the dishwasher off by unscrewing the 11 star type screws. Unplug a couple of wire plug connectors to completely remove the inside of the dishwasher door. Take the three screws out for the plastic control board holder. Unconnect the ribbon cable for the control panel. Becareful, the connector slides on the top to allow the ribbon connector to be disconnect. Unscrew and now remove the control. Reverse the instructions to install the new control panel.

1. Removed door inside plastic panel, 2. Removed additional screws holding panel to hinge brackets and control panel, 3. Figured out that this would all have been easier if I'd unhooked door hinge springs first (access from sides), 4. Removed isulation from old panel and reglued to new panel, 5 Reassembled, hooking up door springs last. Voila!

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Removed the top rack and unscrewed the six screws involved on the rack adjuster. (Take note on how you took the thumb adjuster on top off for easier reassembly) Replace assembly on rack and slide rack back into dish washer. Kudos to PartSelect for getting my part here in less than 24 hours on a normal delivery charge.

You just remove the old unit and set in the new unit. the wheels were already connected.

I removed the inside door panel, unplugged the old assembly and replaced with the new. The only caveat is that I THOUGHT the unit came WITH a new plastic handle, and it did not. It was very difficult to remove the handle from the old unit, and to install it in the new unit. The description was not adequate. I had read other blogs and they warned of the same missing handle, and I thought I had ordered correctly. The repair is fine, but the old handle is cracked, so I dont know how long it will last.

First I made sure the breaker for the appliance was turned off!

I only had to unscrew all the screws from the inside door.

Next I used pliers to pry the old Latch Assembly (it is all pig tailed so only to plugs to undo).

Next, I snapped the new Latch Assembly into the two sockets.

Screws were replaced and wa la!

Turned breaker on and tested. Easy as pie. Took about 10 minutes from collecting the tools, fixing the problem, and replacing all the tools.

I actually had my 14 year old daughter do it so that she could learn how to make small repairs. This would have easily cost approximately $150 for a repairman to come and fix.

Then we went to the garage and unstuck the valve on the carberator to our '75 Chevy! (it was cold).

Not bad for a couple of girls!