MDB8601AWS10 Maytag Dishwasher - Instructions

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

If your model is the same as this one and it stopped working, 98% chance It's the control panel. Remove inner panel of the door. Unscrew the one screw on the control board box to get access to disconnect ribbon wire. Remove four screws two on each side of back of control panel. Install reverse of removal. Done!

Took the new part and ran silicone around the opening for the ribbon cable to prevent steam from entering shock I believe causes this unit to constantly fail. Install the part. Then ran another bead of silicone around the touch pad to prevent water from entering. Hope this stops this unit from failing

I pulled the AC to the device, took the door apart , unscrewed the mounting to the door, unplugged the wires to it, plugged the wires on the new part, screwed it to the door, and finally put the door back together. Oh yeah, had to plug AC back in.

Pried end tabs of track off with fingers, slid upper rack out of dishwasher, removed 5 screws of adjuster assembly from side of upper rack, replaced broken assembly with new assembly and replaced 5 screws, slid upper rack into tracks, replaced end tabs, finished.

Why did I have to buy entire assembly when I only needed one wheel? Original assembly had wheels screwed to assembly, replacement assembly had wheels riveted to assembly. Not appreciated.

I removed the middle rack from the dishwasher being careful to pay attention to how the end stops were located. I put the rack on the kitchen table and with my new parts placed where I could reach them, simply unscrewed the faulty parts and replaced them with the new parts! Couldn't have been easier. I especially appreciated the ease of navigating your web site and locating the parts I needed. I was looking for something entirely different until I read feedback from a previous customer and knew instantly what part I needed!

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

My married daughter actually did the repair. I removed the plastic assemblies that held the upper cage and upper spray assembly. She unscrewed the screws that held the filter/impeller assembly in place and replaced the old one with the new one. I finished the job by cleaning the interior of the washer and putting everything back together. The dishes are sparkling clean again!

Hardest task was finding model number on my ancient dishwasher. Finally just looked at photos and picked the right one. Ordered part and it was here in 24 hours (How do they do that?!!) and it still cost less than at local appliance shop. Carefully kept old screws so I could use them on new adjuster. Part doesn't come with new screws, so watch what you do when you take old one apart. Needed a star screwdriver which I had from a previous repair when I was trying to replace just axle without buying whole new adjuster. Easy enough to do but need a third hand to hold up rack while attaching adjuster.

Quite easy to disassemble the rack arm then replace with new one. I was concerned the part might not fit my dishwasher because it's fairly old and the series numbers were not quite the same, but it fit perfectly. I am very impressed with how quickly I received the part, too.

First, I removed the screw, then I took off the old wash arm, then I replaced the wash arm, and replaced the screw. Nothing could be easier!

Orderd the part's from your web site (recived my order in a timley fasion thanks) the parts just sliped on and clipped' basket rolls great. Mike Schaffer

Easy to repair and saved us replacing a dishwasher that was pretty new as it was. The dishes weren't getting clean, checked it out and found out the chopper was broken. Works great now with clean dishes.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

FIrst I went to your web site; located the part on the easy to read diagram. Next I ordered the part. When the part came to the house (2-3 days), I opened the box and then the packaging, I screwed the part in and Wala! Boom! Bang! She was fixed!

All kidding aside. The part order was quick to locate, quick to ship and one of the easiest companies to deal with. I will return on my next dyi project.